Black Horce Model SUKHOI 31 BH11 Instruction Manual Book Download Page 23 | Manualshive

Page: 23 / 27

background image

SUKHOI 31.

INSTRUCTION MANUAL

23

Drill a hole.

Trim.



3)

Using the hardware provided, mount

the main landing gear to the fuselage.



2) A drop of C/A glue on the wheel collar

screws will help keep them from coming lose
during operation.

Repeat the process for the other wheel.

Secure.

«
...
21
22
23
24
25
...
»

Summary of Contents for SUKHOI 31 BH11




























Reviews:

No comments

Related manuals for SUKHOI 31 BH11

Brand: Eachine Pages: 8

Brand: Old School Model Works Pages: 24

Brand: MTHTrains Pages: 36

MAJO GARAGE MOTOR CITY

Brand: Smoby Pages: 7

Alphabert s Pen Pal Phonics

Brand: VTech Pages: 16

Weaver Nickel Plate Road L1a

Brand: Quality Craft Pages: 6

Brand: The Wings Maker Pages: 13

Brand: Walkera Pages: 22

Brand: Multiplex Pages: 11

Brand: Zapf Creation Pages: 76

Cyber-X C10 Crossover Legacy

Brand: K'Nex Pages: 24

Brand: marklin Pages: 28

P-47 THUNDERBOLT

Brand: Top Flight Models Pages: 16

F-35 Lightning II Joint Strike Fighter

Brand: Freewing Pages: 19

Brand: Horizon Hobby Pages: 18

Brand: Fisher-Price Pages: 6

Brand: Fisher-Price Pages: 16

Control X-RAZOR PRO

Brand: REVELL Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands