Black Horce Model SPEED AIR-40 BH08 Instruction Manual Book Download Page 19 | Manualshive

Page: 19 / 26

background image

19

SPEED AIR-40 _

Item code:BH08.

Instruction Manual.

Rudder servo install as same as method of
elevator servo. See picture below:

RUDDER SERVO INSTALLATION.

Rudder servo.

See picture below:

VERTICAL INSTALLATION.

Hinge.

Rudder servo.

Cut the covering
away from the slot.

Temporary pin to
keep hinge centered.

Assemble then apply drops of thin
C/A to center of hinge,on both sides.



1) Using a modeling knife, remove the

covering from the top of the fuselage and the
covering from over the precut hinge slot cut
into the lower rear portion of the fuselage This
slot accepts the lower vertical.

«
...
17
18
19
20
21
...
»

Summary of Contents for SPEED AIR-40 BH08



























Reviews:

No comments

Related manuals for SPEED AIR-40 BH08

MAISON FORSTIERE 8037

Brand: JEUJURA Pages: 2

Brand: Kasama Pages: 43

Sea King Mk. 41 45 years SAR

Brand: REVELL Pages: 16

Poterie Professional POTTERY Studio

Brand: Buki Pages: 32

Brand: Quick Pages: 32

Brand: BlitzRCWorks Pages: 12

Brand: Faller Pages: 4

Brand: Eduard Pages: 4

HISTORICAL TOWN GATE

Brand: Faller Pages: 8

Brand: marklin Pages: 12

Brand: Faller Pages: 4

Brand: marklin Pages: 32

Wacky Mole Clown

Brand: Spirit Pages: 3

Brand: Train-Tech Pages: 2

Newborn Necessities Gift Set

Brand: VTech Pages: 10

HEXBUG CATAPULT

Brand: Vex Robotics Pages: 40

Brand: Mikado Pages: 13

Brand: KidKraft Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands