5
11
12
13
14
15 16
17
18
19
20
21
22
23
1. Built-in 120 volt AC charger (under protective cover)
2. Ergonomic rubber grip handle
3. Jump-starter power switch
4. Air hose and Sure Fit
®
nozzle
5. Storage compartment cover
6. Nozzle adapter
7. Positive (+) red clamp
8. LED area light
9. Negative (–) black clamp
10. 12 Volt DC Charging Adapter (may be sold separately)
11. Dual 120 volt AC outlets (under protective covers)
12. Air pressure gage
13. Battery status LED indicators
14. Battery power level button
15. Reverse polarity indicator
16. 12 volt DC accessory outlet (under protective cover)
17. Inverter power switch
18. Inverter power indicator
19. Compressor power switch
20. Area light on/off button
21. USB power indicator
22. USB power on/off button
23. USB charging port (under protective cover)
CHARGING/RECHARGING
Lead-acid batteries require routine maintenance to ensure a full charge and long battery life. All batteries lose energy from self-discharge over time and more
rapidly at higher temperatures. Therefore, batteries need periodic charging to replace energy lost through self-discharge. When the unit is not in frequent use,
manufacturer recommends the battery be recharged at least every 30 days.
WARNING: Never attempt to use the AC and DC charging methods at the same time.
Notes:
This unit is delivered in a partially charged state – you must fully charge it before using it for the first time. Initial AC charge should be for 40 hours.
Recharging battery after each use will prolong battery life; frequent heavy discharges between recharges and/or overcharging will reduce battery life.
Make sure all other unit functions are turned off during recharging, as this can slow the recharging process.
CAUTION: RISK OF PROPERTY DAMAGE:
Failure to keep the battery charged will cause permanent damage and result in poor jump starting performance.
IMPORTANT:
If you know the unit is discharged, but the battery status indicators light as if the unit is fully charged when connected to a charging power source,
this may be due to the internal battery having high impedance. The manufacturer suggests leaving the unit charging for a period of 40 hours using the built-in
AC charger before use.
Charging/Recharging Using the 120V AC Charger and a Standard Household Extension Cord (not included)
1. Lift the cover built-in 120V AC charger located on the lower left front of the unit (refer to the Features section to locate). Connect an extension cord to the
unit. Plug the other end of the cord into a standard 120V AC wall outlet.
2. Charge until two red LED battery status indicators light and one green LED battery status indicator lights or flashes.
3. Disconnect the extension cord.
Notes:
The unit cannot be overcharged using the AC method.
The unit will not charge if the inverter power switch is turned on.
Charging/Recharging Using the 12V DC Charging Adapter (may be sold separately)
The DC recharging method will NOT recharge the unit as effectively as recharging from 120 volt AC. The 12 volt DC recharging procedure is recommended only
when it is necessary, since frequent use of the 12 volt DC recharging procedure may shorten the battery system’s life.
Charging the unit from an external 12 volt DC power source requires the use of the 12 Volt DC adapter. This adapter has a male DC connector at each end.
1. Insert the 12 Volt DC Charging Adapter plug with the grooved tip into the vehicle’s 12 volt DC accessory outlet (or other DC power source).
2. Insert the remaining 12 Volt DC Charging Adapter plug into 12V DC accessory outlet on the front panel of the unit.
3. Charge the unit until the green FULL indicator lights when the Battery Power Level Button is pressed (with the adapter unplugged from the unit). DO NOT
CHARGE MORE THAN 6 HOURS MAXIMUM USING THIS METHOD.
4. When charging is complete, remove the charging cord and store in a safe place.
Notes:
Some vehicles require that the ignition be switched to the accessory outlet position in order to power the accessory outlet.
Do not leave the unit unattended when charging using the this method.
JUMP-STARTER
This Jump-Starter is equipped with an On/Off Power Switch. Once the connections are properly made, turn the switch on to jump-start the vehicle.
1. Turn off vehicle ignition and all accessories (radio, A/C, lights, connected cell phone chargers, etc.). Place vehicle in “park” and set the emergency brake.
2. Make sure the Jump-Starter Power Switch is turned to off.
3. Remove jumper clamps from clamp tabs. Connect the red clamp first, then the black clamp.
4. Procedure for jump-starting a NEGATIVE GROUNDED SYSTEM (negative battery terminal is connected to chassis) (MOST COMMON)
4a. Connect positive (+) red clamp to vehicle battery’s positive terminal.
4b. Connect negative (–) black clamp to chassis or a solid, non-moving, metal vehicle component or body part. Never clamp directly to negative battery
terminal or moving part. Refer to the automobile owner’s manual.
5. Procedure for jump-starting POSITIVE GROUND SYSTEMS
Notes:
In the rare event that the vehicle to be started has a Positive Grounded System (positive battery terminal is connected to chassis), replace steps 4a and 4b above with steps 5a and
5b, then proceed to step 6.
5a. Connect negative (–) black clamp to vehicle battery’s negative terminal.
Summary of Contents for PRH5BCA
Page 1: ...20 20 20...
