Black+Decker KA401, Manual

Page: 5 / 60

5
ENGLISH (Original instructions)
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the
trigger time.
Labels on tool
The following symbols are shown on the tool along with the
date code:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Electrical safety
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate..
u
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
1. On/off switch
2. Dustbag
3. Dust extraction outlet
4. Sanding base
5. Paper clamp lever
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting sanding sheets (fig. A & B)
Warning! Never use the tool without a sanding sheet or
accessory in place.
Fitting sanding sheets with nylon loops (fig. A)
Warning! Make sure that the tool is switched off and
unplugged.
u
Press the sheet firmly and evenly onto the sanding
base(4), making sure that the holes in the sheet line up
with the holes in the base.
Fitting regular sanding sheets (fig. B)
Warning! Make sure that the tool is switched off and
unplugged.
u
Soften the sanding sheet by rubbing its non-abrasive side
over the edge of a worktop.
u
Press the paper clamp levers (5) upwards to release them
from the retaining grooves and open the paper clamps (5)
by pressing them down.
u
Insert the edge of the sanding sheet into the front paper
clamp (5) as shown.
u
Press the front paper clamp lever (5) downwards and
locate it in the retaining groove.
u
While keeping a slight tension on the sheet, insert the rear
edge of the sheet into the rear paper clamp (5).
u
Press the rear paper clamp lever (5) downwards and
locate it in the retaining groove.
Louvre attachment (For KA401L only) (fig. C)
With this attachment you can work in crevices and use the
sanding base on both sides.
u
Locate the front of the louvre attachment (7) onto the
sanding base (4).
u
Secure it in position with the four screws supplied.
u
Place a 1/2 sheet to the underside of the louvre base. Part
of it will fold over the front part of the base.
u
To remove the louvre attachment (7), reverse the
procedure.
Fitting and removing the dustbag (fig. D)
u
Fit the dustbag (2) over the dust extraction outlet(3).
u
Slide the dustbag (2) onto the tool and make sure that it is
securely located.
u
To remove the dustbag (2), pull it to the rear and off the
outlet.
Use
Warning! Let the tool work at its own pace. Do not overload.
Switching on and off (fig. E)
u
To switch the tool on, press the part of the on/off switch (1)
marked 'I' .
u
To switch the tool off, press the part of the on/off switch (1)
marked '0' .
Emptying the dustbag
u
The dustbag (2) should be emptied every 10 minutes.
u
Shake the dustbag (2) to empty the contents.
Hints for optimum use
u
Do not place your hands over the ventilation slots.
u
Do not exert too much pressure on the tool.
u
Regularly check the condition of the sanding sheet.
Replace when necessary.
u
Always sand with the grain of the wood.
u
When sanding new layers of paint before applying another
layer, use extra fine grit.