8
ENGLISH
u
Re-insert the battery (5).
u
If the charging indicators continues flashing red at a fast
rate, use a different battery to determine if the charging
process works properly.
u
If the replaced battery charges correctly, the original
battery is defective and should be returned to a service
centre for recycling.
u
If the new battery gives the same indication as the original
battery, take the charger to be tested at an authorised
services centre.
Note: It may take as long as 60 minutes to determine that
the battery is defective. If the battery is too hot or too
cold, the LED will alternately blink red, fast and slow, one
flash at each speed and repeat.
Selecting the torque or drill position (fig. D)
This tool is fitted with a collar to set the torque for tightening
screws.
u
For drilling, set the collar (8) to the drilling position by
aligning the symbol with the marking (14).
u
For screwdriving, set the collar to the desired setting.
u
If you do not yet know the appropriate setting, proceed as
follows:
t
Set the collar (8) to position 1.
t
Tighten the first screw.
t
If the clutch ratchets before the desired result is
achieved, increase the collar setting and continue
tightening the screw. Repeat until you reach the correct
setting.
Selecting the direction of rotation (fig. E)
For drilling and tightening screws,
use forward (clockwise) rotation. For loosening screws or
removing a jammed drill bit, use reverse (counterclockwise)
rotation.
u
To select forward rotation, push the forward/reverse slider
(2) to the left.
u
To select reverse rotation, push the forward/reverse slider
to the right.
u
To lock the tool, set the forward/reverse slider into the
centre position.
Drilling/screwdriving
u
Select forward or reverse rotation using the forward/re-
verse slider (2).
u
To switch the tool on, press the variable speed switch (1).
The tool speed depends on how far you press the switch.
u
To switch the tool off, release the variable speed switch.
Drilling in masonry (fig. F)
u
For drilling in masonry, set the torque adjustment collar (8)
to the hammer drilling position by aligning the symbol
with the marking.
u
Slide the speed selector (13) towards the front of the tool
(2nd gear).
NOTE: For other torque adjustment collar settings and fea-
tures, refer to the manual provided with your power tool.
Speed selector (fig. F)
u
For drilling in steel and for screwdriving applications, slide
the speed selector (13) towards the rear of the tool (1st
gear).
u
For drilling in materials other than steel, slide the speed
selector (13) towards the front of the tool (2nd gear).
BIT TIP STORAGE
A magnetic bit storage slot (4) is built into the area on the top
of the tool.
LED WORK LIGHT
When drill is activated by pulling the trigger switch (1), the
integrated LED work light (10) will automatically illuminate the
work area.
NOTE:
The work light is for lighting the immediate work
surface and is not intended to be used as a flashlight.
Hints for optimum use
Drilling
u
Always apply a light pressure in a straight line with the drill
bit.
u
Just before the drill tip breaks through the other side of the
workpiece, decrease pressure on the tool.
u
Use a block of wood to back up workpieces that may
splinter.
u
Use spade bits when drilling large diameter holes in wood.
u
Use HSS drill bits when drilling in metal.
u
Use masonry bits when drilling in soft masonry.
u
Use a lubricant when drilling metals other than cast iron
and brass.
u
Make an indentation using a centre punch at the centre of
the hole to be drilled in order to improve accuracy.
Screwdriving
u
Always use the correct type and size of screwdriver bit.
u
If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
u
Always hold the tool and screwdriver bit in a straight line
with the screw.
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER and Piranha accessories are engineered
to high quality standards and designed to enhance the perfor-
mance of your tool. By using these accessories you will get
the very best from your tool.
Summary of Contents for EVO186
Page 1: ...English 4 Bahasa Indonesia 10 EVO186 ...
Page 2: ...2 C A B 12 11 5 E D 8 13 ...
Page 3: ...3 F 8 13 9 ...
