background image

ServSwitch Agility and Agility Dual

724-746-5500   |   blackbox.com 

Page 4

Instrucciones de Seguridad

(Normas Oficiales Mexicanas Electrical Safety Statement)

1.  Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado.

2.  Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura.

3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación deben ser respetadas.

4.  Todas las instrucciones de operación y uso deben ser seguidas.

5.  El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de la tina de baño, lavabo, sótano mojado o cerca 

de una alberca, etc..

6.  El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean recomendados por el fabricante. 

7.  El aparato eléctrico debe ser montado a la pared o al techo sólo como sea recomendado por el fabricante.

8.  Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a lo descrito en las instrucciones de operación. 

Todo otro servicio deberá ser referido a personal de servicio calificado. 

9.  El aparato eléctrico debe ser situado de tal manera que su posición no interfiera su uso. La colocación del aparato eléctrico 

sobre una cama, sofá, alfombra o superficie similar puede bloquea la ventilación, no se debe colocar en libreros o gabinetes 
que impidan el flujo de aire por los orificios de ventilación.

10.  El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como radiadores, registros de calor, estufas u otros 

aparatos (incluyendo amplificadores) que producen calor.

11.  El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo descrito en el instructivo de operación, o como 

se indique en el aparato.

12.  Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea eliminada.

13.  Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados 

sobre o contra ellos, poniendo particular atención a los contactos y receptáculos donde salen del aparato.

14.  El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomendaciones del fabricante.

15.  En caso de existir, una antena externa deberá ser localizada lejos de las lineas de energia.

16.  El cable de corriente deberá ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo.

17.   Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilación.

18.  Servicio por personal calificado deberá ser provisto cuando: 

A:  El cable de poder o el contacto ha sido dañado; u 
B:  Objectos han caído o líquido ha sido derramado dentro del aparato; o 
C:  El aparato ha sido expuesto a la lluvia; o 
D:  El aparato parece no operar normalmente o muestra un cambio en su desempeño; o 
E:  El aparato ha sido tirado o su cubierta ha sido dañada.

Summary of Contents for ServSwitch Agility ACR1000A















































Reviews: