background image

 724-746-5500   |   blackbox.com

Page 4

Black Box Short Range Modem

WARRANTY INFORMATION

Black Box warrants all ME475A-R2 components to be free from defects, and will—at 
our option—repair or replace the product should it fail within one year from the first 
date of the shipment.

This warranty is limited to defects in workmanship or materials, and does not cover 
customer damage, abuse or unauthorized modification. If this product fails or does not 
performs as warranted, your sole recourse shall be repair or replacement as described 
above. Under no condition shall Black Box be liable for any damages incurred by the 
use of this product. These damages include, but are not limited to, the following: lost 
profits, lost savings and incidental or consequential damages arising from the use of or 
inability to use this product. Black Box specifically disclaims all other warranties, 
expressed or implied, and the installation or use of this product shall be deemed an 
acceptance of these terms by the user.

RADIO AND TV INTERFERENCE

The ME475A-R2 generates and uses radio frequency energy, and if not installed and 
used properly—that is, in strict accordance with the manufacturer’s instructions—may 
cause interference to radio and television reception. The ME475A-R2 has been tested 
and found to comply with the limits for a Class A computing device in accordance with 
specifications in Subpart B of Part 15 of FCC rules, which are designed to provide rea-
sonable protection from such interference in a commercial installation. However, there 
is no guarantee that interference will not occur in a particular installation. If the l 
ME475A-R2 does cause interference to radio or television reception, which can be 
determined by disconnecting the RS-232 interface, the user is encouraged to try to 
correct the interference by one or more of the following measures: moving the comput-
ing equipment away from the receiver, re-orienting the receiving antenna and/or plug-
ging the receiving equipment into a different AC outlet (such that the computing 
equipment and receiver are on different branches).

CE NOTICE

The CE symbol on your Black Box equipment indicates that it is in compliance with the 
Electromagnetic Compatibility (EMC) directive and the Low Voltage Directive (LVD) of 
the European Union (EU). A Certificate of Compliance is available by contacting Tech-
nical Support.

Summary of Contents for ME475A-R2

































Reviews: