Black Box LW6005A-R2 Manual Download | Manualshive

Page: 75 / 102

background image

75

2.6.6 Static Routing

This router provides Static Routing function when NAT is disabled. With Static Routing,
the router can forward packets according to your routing rules. The IP sharing function
will not work any more in Static Routing mode.

Note:

The DMZ function of firewall will not work if static routing is enabled.

Parameter

Description

Enable Static Routing

Static Routing function is default disabled. You
have to enable the Static Routing function before
your routing rules take effect.

Destination LAN IP

The network address of destination LAN.

Subnet Mask

The subnet mask of destination LAN.

Default Gateway

The next stop gateway of the path toward the
destination LAN. This is the IP of the neighbor
router that this router should communicate with on
the path to the destination LAN.

«
...
73
74
75
76
77
...
»

Summary of Contents for LW6005A-R2







































































































Reviews:

No comments

Related manuals for LW6005A-R2

Brand: NETGEAR Pages: 263

AceroDURO 100/S100

Brand: CNC-Step Pages: 86

Brand: Link-One Pages: 77

WI DRIVE WID11GEN

Brand: Dension Pages: 26

UniFi AP FlexHD

Brand: Ubiquiti Pages: 22

Brand: ZyXEL Communications Pages: 2

WAP11 - Instant Wireless Network Access Point

Brand: Linksys Pages: 33

Brand: D-Link Pages: 40

Brand: D-Link Pages: 46

Brand: D-Link Pages: 24

Brand: D-Link Pages: 23

DWL-3140AP - Web Smart PoE Thin Access Point

Brand: D-Link Pages: 72

Brand: D-Link Pages: 46

DWL-2130AP - xStack - Wireless Access Point

Brand: D-Link Pages: 12

Brand: D-Link Pages: 8

DWL-2230AP - xStack - Wireless Access Point

Brand: D-Link Pages: 12

DWL-2100AP - AirPlus Xtreme G

Brand: D-Link Pages: 2

Brand: D-Link Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands