6
ENGLISH
X
The charging indicator (9) will be lit as long as the
battery pack is connected to the plugged-in charger.
X
Charge discharged batteries within 1 week. Battery life
will be greatly diminished if stored in a discharged state.
Charge indicators
If the charger detects a problem with a battery pack, the
charge indicator (9) will flash at a fast rate.
X
If this occurs, re-insert the battery pack (7).
X
If the problem persists, put a different battery pack in the
charger to determine if the charger is OK.
X
If the new battery pack charges correctly, then the
original battery pack is defective and should be returned
to a service centre for recycling.
X
If the new battery pack gives the same indication as the
original, take the charger to be tested at an authorized
service centre.
Note:
It may take as long as fifteen minutes to determine that
the pack is defective.
If the battery pack is too hot or too cold, the LED will
alternately blink fast and slow, one flash at each speed and
repeat.
Battery chargers - daisy chaining (fig. C)
Single and dual port chargers can be electrically connected
in any order up to a maximum of 4 chargers. Each charger
has a power-in cord (10) which plugs into the electrical outlet
and a power-out cord (11) which plugs into the next charger.
To connect the chargers in a daisy chain:
X
Plug the power-in cord (10) into an electrical outlet.
X
Remove the power-in cord from the next charger and
plug in the power-out cord (11) rom the charger that is
now plugged into the outlet.
X
Repeat this process for the remaining chargers.
Chargers that are daisy chained together operate
independently as though each one was plugged into a
separate outlet, therefore a battery can be removed from
anywhere along the daisy chain without affecting the other
chargers.
Use
Switching on and off (fig. D)
X
To switch the tool on, press the on/off trigger switch (6).
X
To switch the tool off, release the on/off trigger
switch (6).
X
A forward/reverse control button (3) determines the
direction of the tool and also serves as a lock off button.
X
To select forward rotation, release the on/off trigger
switch (6) and move the forward/reverse control button
(3) to the left.
X
To select reverse direction, move the forward/reverse
control button (3) in the opposite direction.
X
The centre position of the control button (3) locks the
tool in the off position. Make sure that the on/off trigger
switch (6) is released before changing the position of
the forward/reverse control button (3).
High/low speed selector (fig. D)
The 2-speed feature of your screwdriver allows for greater
versatility.
X
To select the low speed, high torque setting (position 1),
turn the tool off and allow it to stop. Move the speed
selector switch (2) to the right.
X
To select the high speed, low torque setting (position 2),
turn the tool off and allow it to stop. Move the speed
selector switch (2) to the left.
Warning!
Do not move the speed selector button with the
tool switched on.
Quick release collar (fig. E)
Note:
The collar accepts 1/4" hex accessories only.
To install a screwdriver bit or other accessory, pull the collar
(1) back and insert the bit into the collar until it locks into
place.
To remove a screwdriver bit or other accessory, pull the
collar (1) back. Remove the bit and release the collar.
Driving screws
X
When driving screws, the forward/reverse button (3)
should be pushed to the left.
X
Move the forward/reverse button (3) pushed to the right
for removing screws.
Maintenance
Your Black & Decker tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning!
Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
X
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
X
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
X
Regularly open the chuck and tap it to remove any dust
from the interior.
