6
4 . Procedure for jump-starting a NEGATIVE GROUNDED SYSTEM (negative battery terminal is connected to
chassis) (MOST C O M M O N )
4 a . Connect positive (+) red clamp to vehicle battery ’s positive terminal.
4 b . Connect negative (–) black clamp to chassis or a solid, non-moving, metal vehicle component or body
part. Never clamp directly to negative battery terminal or moving part.
5 . Procedure for jump-starting POSITIVE GROUND SYSTEMS
Note:
In the rare event that the vehicle to be started has a Positive Grounded System (positive battery terminal
is connected to chassis), replace steps 4a and 4b above with steps 5a and 5b, then proceed to step 6.
5 a . Connect negative (–) black clamp to vehicle battery ’s negative terminal.
5 b . Connect positive (+) red clamp to vehicle chassis or a solid, non-moving, metal vehicle component or body
part. Never clamp directly to Positive battery terminal or moving part.
6 . When clamps are connected properly, turn the Jump-Starter Power Switch to ON.
7 . Turn ON the ignition and crank the engine in 5-6 second bursts until engine starts.
8 . Turn the Jump-Starter Power Switch back to the OFF position.
9 . Disconnect the negative (–) engine or chassis clamp first, then disconnect the positive (+) battery clamp.
FOLLOW ALL SAFETY INSTRUCTIONS FOUND IN THIS MANUAL.
CAUTIONS: RISK OF PROPERTY DAMAGE
• If the connections to the battery ’s P O S I T I V E and N E G AT I V E terminals are incorrect, the Reverse Polarity
Indicator will light (red) and the unit will sound a beep. Disconnect clamps and reconnect to battery with
correct polarity.
• If vehicle fails to start, turn OFF the ignition, turn OFF the Jump-Starter Power Switch, disconnect the jump-start
s y s t e m ’s leads and contact a qualified technician to investigate why the engine did not start.
• Recharge this unit fully after each use.
WARNINGS
• Jump-Starter Power Switch should be off prior to jump-starting.
• This power system is to be used ONLY on vehicles with 12 volt DC battery systems.
• Never touch red and black clamps together — this can cause dangerous sparks, power arcing, and/or explosion.
• Vehicles that have on-board computerized systems may be damaged if vehicle battery is jump-started. Before
jump-starting this type of vehicle, read the vehicle manual to confirm that external-starting assistance is advised.
• Excessive engine cranking can damage the vehicle‘s starter motor. If the engine fails to start after the recommended
number of attempts, discontinue jump-start procedure and look for other problems that need to be corrected.
• After use, turn the Jump-Starter Power Switch OFF.
• Replace worn or defective parts immediately — contact the Customer Service Department toll free (800)
5 4 4 - 6 9 8 6 .
12 VOLT DC PORTABLE POWER SUPPLY
This portable power source is also for use with all 12 volt DC accessories equipped with a male accessory
outlet plug and are rated up to 5 amps.
1 . Lift up the cover of the unit ‘s 12 volt DC outlet.
2 . Insert the 12 volt DC plug from the appliance into the 12 volt accessory outlet on the unit.
DO NOT EXCEED
A 5 AMP LOAD.
3 . Switch on the appliance and operate as usual.
4 . Periodically press the battery charge level pushbutton to check battery status.
EMERGENCY AREA LIGHT
The area light is controlled by the Area Light Power Switch on the front panel of the unit. Make sure the lamp is
turned OFF when the unit is being recharged or stored.
PORTABLE INFLATOR
The built-in 12 volt DC inflator is the ultimate inflator for all vehicle tires, trailer tires and recreational inflatables.
Three different sized nozzles are supplied. Each nozzle will clip on the end of the standard tire valve connector
located at the free end of the inflator hose. The inflator nozzles are stored inside the hose hatch. The inflator
hose with tire fitting is stored in a retaining channel between the jumper cable channels on the rear of the unit.
The ON/OFF Switch is located on the back of the Main Unit. The inflator can operate long enough to fill up to 3
average sized tires before the battery must be recharged.
JS450CP ManualEN 062807.qxp 9/26/08 12:42 PM Page 6
