ENGLISH • 13
making
any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool.
Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Pad
2. Handles
3. On/Off switch
4. Cord Set
5. Bonnet
ADITIONAL POWER TOOL
SAFETY WARNINGS
Warning! Additional safety warnings for polisher.
Your BLACK+DECKER polisher has been designed for
sanding and polishing wood, metal, plastics and painted
surfaces. This tool is intended for consumer use only.
f
Hold power tool by insulated gripping surfaces,
because the belt may contact its own cord. Cutting
a “live” wire may make exposed metal parts of the
power tool “live” and shock the operator.
f
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
Warning! Contact with or inhalation of dusts arising
from polishing applications may endanger the health of
the operator and possible bystanders. Wear a dust mask
specifically designed for protection against dust and fumes
and ensure that persons within or entering the work area
are also protected.
f
Thoroughly remove all dust after polishing.
f
Take special care when sanding paint which is
possibly lead based or when sanding some woods
and metal which may produce toxic dust:
f
Do not let children or pregnant women enter the
work area.
f
Do not eat, drink or smoke in the work area.
f
Dispose of dust particles and any other debris
safely.
f
This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety. Children should be
supervised to ensure that they do not play with the
appliance.
f
The intended use is described in this instruction
manual. The use of any accessory or attachment
or performance of any operation with this tool other
than those recommended in this instruction manual
may present a risk of personal injury and/or damage
to property.
ASSEMBLY AND ADJUSTMENT
Prior to assembly and adjustment always unplug the tool.
Fitting the bonnet (Fig. B)
Place the bonnet (5) onto the pad (1) as shown. It is
recommended to position on the 3 feet when unit upside-
down. Make sure the bonnet is fitted securely and evenly
around the underside of the pad.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n
0
....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
