10
E N G L I S H
◆
To charge the battery, set the
tool to the straight position
and insert the charger plug
(10) into the connector (11).
◆
Plug in the charger. Switch on
at the mains.
◆
Leave the tool connected to the
charger for at least 12 hours.
The tool can be left connected to
the charger indefinitely.
The charger may hum and become
warm while charging; this is normal
and does not indicate a problem.
◆
Before using the tool, unplug
the charger and disconnect
the tool from the charger.
Do not use the tool while it
is connected to the charger.
Adjusting the handle (fig. D)
For optimum versatility, the
handle can be set to different
positions.
◆
Press the handle adjustment
button (4).
◆
Swivel the handle into the
desired position.
◆
Release the button.
KC9036 - Manual spindle lock
(fig. E)
The manual spindle lock allows
you to use the tool as a regular
screwdriver. You can give an
extra twist to firmly tighten a
screw or to loosen a very tight
screw.
◆
To activate the spindle lock,
turn the collar (2) to the
symbol. With the spindle lock
activated, the tool cannot be
switched on.
◆
To release the spindle lock,
turn the collar (2) to the
symbol.
KC9039 - Setting the torque
(fig. E)
This tool is fitted with a collar to
set the torque for tightening
screws.
Large screws and hard workpiece
materials require a higher torque
setting than small screws and soft
workpiece materials. The collar
has a wide range of settings to
suit your application.
◆
Turn the collar (2) to the
desired setting. If you do not
yet know the appropriate
setting, proceed as follows:
-
Set the collar to the lowest
torque setting.
-
Tighten the first screw.
-
If the clutch ratchets before
the desired result is achieved,
increase the collar setting and
continue tightening the
screw. Repeat until you reach
the correct setting. Use this
setting for the remaining
screws.
Operating the tool (fig. F)
◆
Make sure that the spindle
lock is released.
◆
To tighten a screw or nut,
slide the on/off switch (1) to
the right and press it.
◆
To loosen a screw or nut,
slide the on/off switch (1) to
the left and press it.
◆
To switch the tool off, release
the on/off switch.
Hints for optimum use
◆
Always use the correct type
and size of screwdriver bit.
◆
If screws are difficult to
tighten, try applying a small
amount of washing liquid or
soap as a lubricant.
◆
Use the spindle lock to loosen
very tight screws or to firmly
tighten screws.
◆
Always hold the tool and
screwdriver bit in a straight
line with the screw.
◆
When screwing in wood, it is
recommended to drill a pilot
hole with a depth equal to
the length of the screw.
KC9036EUR.PM65
25-06-2001, 14:53
10
Summary of Contents for KC9036
Page 1: ...1 KC9036 KC9039 KC9036EUR PM65 25 06 2001 14 53 1 ...
Page 3: ...3 A B C 2 1 4 5 6 3 7 9 8 10 11 KC9036EUR PM65 25 06 2001 14 53 3 ...
Page 4: ...4 D KC9036 2 E 2 4 KC9039 KC9036EUR PM65 25 06 2001 14 53 4 ...
Page 5: ...5 F G 1 KC9036EUR PM65 25 06 2001 14 53 5 ...
