background image

7

ENGLISH

(Original instructions)

Winding a new cutting line onto an empty spool 

You may wind new cutting line onto an empty spool.
Replacement packs of cutting line are available from your 
Black & Decker dealer (cat. no. A6170 (25 m), A6046 (37.5 m)  
& A6171 (40 m).

  Remove the empty spool from the tool as described 

above.

  Remove any remaining cutting line from the spool.

  Feed 2 cm of cutting line into one of the holes (17) in the 

spool as shown.

  Wind the cutting line onto the spool in the direction of the 

arrow (18). Make sure to wind the line on neatly and in 
layers. Do not criss-cross.

  Let the line protrude approximately 10 cm from the spool 

 

Warning!

 Only use the appropriate type of Black & Decker 

cutting line.

Troubleshooting

If your tool seems not to operate properly, follow the 
instructions below. If this does not solve the problem, please 
contact your local Black & Decker repair agent.

Warning!

 Before proceeding, unplug the tool.

Appliance runs slowly

  Check that the spool housing can rotate freely. Carefully 

clean it if necessary.

  Check that the cutting line does not protrude more than 

11 cm from the spool housing. If it does, cut it off so that it 
just reaches the line trimming blade.

If the bump feed does not work

  Keep the tabs depressed and remove the spool cover 

from the housing.

  Pull the cutting line until it protrudes 11 cm from the 

install a new spool of cutting line as instructed above.

  Align the tabs on the spool cover with the cut outs in the 

housing.

 Push the cover onto the housing until it snaps securely 
into place.

  If the cutting line protrudes beyond the trimming blade, 

cut it off so that it just reaches the blade.

If the bump feed still does not work or the spool is jammed, try 
the following suggestions:

 Carefully clean the spool cover and housing.

 Remove the spool and check that the spring is in place.

  Remove the spool and unwind the cutting line, then wind it 

on neatly again as described above. Replace the spool as 
instructed.

Maintenance

Your Black & Decker corded/cordless appliance/tool has been 
designed to operate over a long period of time with a minimum 
of maintenance. Continuous satisfactory operation depends 
upon proper tool/appliance care and regular cleaning.

Warning!

 Before performing any maintenance on corded/

cordless power tools:

  Switch off and unplug the appliance/tool.

  Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

  Or run the battery down completely if it is integral and then 

switch off.

  Unplug the charger before cleaning it. Your charger does 

not require any maintenance apart from regular cleaning.

  Regularly clean the ventilation slots in your tool/appliance 

and charger using a soft brush or dry cloth.

  Regularly clean the motor housing using a damp cloth. Do 

not use any abrasive or solvent-based cleaner.

Protecting the environment

Separate collection. This product must not be 
disposed of with normal household waste.

needs replacement, or if it is of no further use to you, do not 
dispose of it with household waste. Make this product 
available for separate collection.

 

Separate collection of used products and packaging 
allows materials to be recycled and used again. 
Re-use of recycled materials helps prevent 
environmental pollution and reduces the demand for 
raw materials.

Local regulations may provide for separate collection of 
electrical products from the household, at municipal waste 
sites or by the retailer when you purchase a new product.

 

Summary of Contents for GL310-XE











Reviews: