8
♦
Place the disc onto the spindle as shown (
fi
g. D).
If the disc has a raised centre, make sure that the
raised centre faces the inner
fl
ange.
♦
Make sure that the disc locates correctly on the
inner
fl
ange.
♦
Place the outer
fl
ange (12) onto the spindle. When
fi
tting a grinding disc, the raised centre on the
outer
fl
ange must face towards the disc. When
fi
tting a cutting disc, the raised centre on the outer
fl
ange must face away from the disc.
♦
Keep the spindle lock (6) depressed and tight-
en the outer
fl
ange using the two-pin spanner
(
fi
g. E-F).
Removing
♦
Keep the spindle lock (6) depressed and loosen
the outer
fl
ange (12) using the two-pin spanner.
♦
Remove the outer
fl
ange (12) and the disc.
Fitting and removing sanding discs (
fi
g. F)
For sanding, a backing pad is required. The backing
pad is available from your Black & Decker dealer as
an accessory.
Fitting
♦
Place the inner
fl
ange (11) onto the spindle as
shown (
fi
g. F). Make sure that the
fl
ange is cor-
rectly located on the
fl
at sides of the spindle.
♦
Place the backing pad onto the spindle.
♦
Place the sanding disc onto the backing pad.
♦
Place the outer
fl
ange (12) onto the spindle with
the raised centre facing away from the disc.
♦
Keep the spindle lock (6) depressed and tighten
the outer
fl
ange using the two-pin spanner (
fi
g. F).
Make sure that the outer
fl
ange is
fi
tted correctly
and that the disc is clamped tightly.
Removing
♦
Keep the spindle lock (6) depressed and loosen
the outer
fl
ange (12) using the two-pin spanner
(
fi
g. F).
♦
Remove the outer
fl
ange (12), the sanding disc
and the backing pad.
Use
Warning!
Let the tool work at its own pace. Do not
overload.
♦
Carefully guide the cable in order to avoid ac-
cidentally cutting it.
♦
Be prepared for a stream of sparks when the
grinding or cutting disc touches the workpiece.
♦
Always position the tool in such a way that the
guard provides optimum protection from the grind-
ing or cutting disc.
Switching on and off
♦
To switch on, slide the on/off switch (1) forward.
Note that the tool will continue running when you
release the switch.
♦
To switch off, press the rear part of the on/off
switch.
Warning!
Do not switch the tool off while under load.
Hints for optimum use
♦
Firmly hold the tool with one hand around the
side handle and the other hand around the main
handle.
♦
When grinding, always maintain an angle of ap-
prox. 15° between the disc and the workpiece
surface (
fi
g. G).
Maintenance
Your Black & Decker corded/cordless appliance/tool
has been designed to operate over a long period of
time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care
and regular cleaning.
Warning!
Before performing any maintenance on
corded/cordless power tools:
♦
Switch off and unplug the appliance/tool.
♦
Or switch off and remove the battery from the
appliance/tool if the appliance/tool has a separate
battery pack.
♦
Or run the battery down completely if it is integral
and then switch off.
♦
Unplug the charger before cleaning it. Your charg-
er does not require any maintenance apart from
regular cleaning.
♦
Regularly clean the ventilation slots in your appli-
ance/tool/charger using a soft brush or dry cloth.
♦
Regularly clean the motor housing using a damp
cloth. Do not use any abrasive or solvent-based
cleaner.
♦
Regularly open the chuck and tap it to remove
any dust from the interior (when
fi
tted).
Protecting the environment
Separate collection. This product must not
be disposed of with normal household waste.
Should you
fi
nd one day that your Black & Decker
product needs replacement, or if it is of no further use
to you, do not dispose of it with household waste. Make
this product available for separate collection.
Separate collection of used products and
packaging allows materials to be recycled
and used again. Re-use of recycled materials
helps prevent environmental pollution and
reduces the demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at munici-
pal waste sites or by the retailer when you purchase
a new product.
Black & Decker provides a facility for the collection
and recycling of Black & Decker products once they
have reached the end of their working life. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
