8
9
• Do not use charger if cords or clamps have been damaged in any way — call Technical Support
toll-free at 1-877-571-2391.
• There are no user-serviceable parts in this unit.
• Do not open the unit. In the event of malfunction, it must be returned to manufacturer for
professional testing and repair. Opening the unit will void the manufacturer’s warranty.
Fuse Replacement (DC Accessory Adapter)
1. Disconnect AC power from the outlet and disconnect adaptor from the output cord.
2. Remove plug from accessory outlet. Remove the plastic cap by turning counter clockwise and
lifting off.
3. Remove center pin and spring. Remove fuse.
4. Replace fuse with same type and size fuse (5 amp).
5. Replace center pin and spring inside plug.
6. Replace the plastic cap by turning clockwise.
ACCEssORIEs
Recommended accessories for use with your tool are available from your local dealer. If you need
assistance regarding accessories, please contact manufacturer at 1-877-571-2391.
WARNING:
The use of any accessory not recommended for use with this appliance could be
hazardous.
sERVICE INFORMATION
Whether you need technical advice, repair, or genuine factory replacement parts, contact the
manufacturer at 1-877-571-2391.
FULL ONE-YEAR HOME UsE wARRANTY
The manufacturer warrants this product against defects in materials and workmanship for a period
of ONE (1) YEAR from the date of retail purchase by the original end-user purchaser (“Warranty
Period”).
If there is a defect and a valid claim is received within the Warranty Period, the defective product can
be replaced or repaired in the following ways: (1) Return the product to the retailer where product
was purchased for an exchange (provided that the store is a participating retailer). Returns to retailer
should be made within the time period of the retailer’s return policy for exchanges only (usually 30
to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their
specific return policy regarding returns that are beyond the time set for exchanges. (2) Return the
product to the manufacturer for repair or replacement at manufacturer’s option. Proof of purchase
may be required by manufacturer.
This warranty does not apply to accessories, bulbs, fuses and batteries; defects resulting from normal
wear and tear, accidents; damages sustained during shipping; alterations; unauthorized use or repair;
neglect, misuse, abuse; and failure to follow instructions for care and maintenance for the product.
This warranty gives you, the original retail purchaser, specific legal rights and you may have other
rights which vary from state to state or province to province. This product is not intended for
commercial use.
Please complete the Product Registration Card and return within 30 days from purchase of the
product to: Baccus Global LLC, 595 S. Federal Highway, Suite 210, Boca Raton, FL 33432.
Baccus
Global LLC, toll-free number: 1-877-571-2391.
FREE WARNING LABEL REPLACEMENT:
If your warning labels become illegible or are missing, call
1-877-571-2391 for a free replacement.
spECIFICATIONs
Input:
120V AC
~
60 Hz 0.3A
Output:
6.3V/12.6V DC ...– 1.0A
DC Accessory Plug Fuse:
5A DC
Imported by Baccus Global LLC, 595 S. Federal Highway, Suite 210, Boca Raton, FL 33432
www.Baccusglobal.com • 1-877-571-2391
1. Remove the nuts from the bolts of the battery post’s connectors.
2. Position the RED terminal on the bolt of the POSITIVE battery post connector.
3. Position the BLACK terminal on the NEGATIVE post connector; then replace the nuts.
4. If there is any problem connecting the output leads, check with a reputable auto supply store or
contact the Customer Service Department toll-free at 1-877-571-2391 for assistance in finding an
appropriate connection device for your particular application.
CHARGING WITH THE TERMINAL RINGS
1. Disconnect AC power cord from AC power outlet
2. Disconnect battery terminal clamps and DC accessory plug from the maintainer output cable, at
connector
3. With the ring terminals connected (fig. 3a) and with ring terminal connector held as far away from
battery, connect to the maintainer output cord. If the maintainer red LED is lit, check ring terminal
connections at battery.
4. Slide the voltage selector switch to 6V or 12V
5. Connect AC power
6. The unit should be working with blinking green LED, indicating the battery is being charged.
7. Leave the unit on.
8. Monitor the battery from time to time.
Connecting the Maintainer and Maintaining the Battery with the DC Accessory plug
The charger’s output leads also contain a DC accessory plug.
1. Slide the Voltage Selector switch to 6v or 12v.
2. Insert the DC plug into the vehicle’s DC accessory outlet.
3. Insert the AC plug of the charger into any standard 110/120 volt AC wall outlet.
4. Leave the unit on.
5. Monitor the battery from time to time.
Note:
Some vehicles require that the ignition be turned to the ACC (accessory) position to activate the DC accessory outlet. If your vehicle
ignition is required to be turned to the ACC
position, be sure all the vehicle accessories (i.e. heater, fan, radio, TV, lights... etc) are turned off. If not turned off, the maintainer
might not be able to maintain the battery.
TROUBLEsHOOTING
WARNING:
During troubleshooting, if there is a need to connect/disconnect the unit from battery,
follow the steps outlined in “Important Safety Instructions” at the front of this manual and the warning
“To reduce risk of a spark near the battery”.
Common Problem
Possible Solutions
Unit not charging
• Check that the charger is properly connected to a live 120 volt
AC outlet (the LED will illuminate).
• Check that the correct voltage setting has been selected for the
battery being maintained.
• If the battery to be maintained has fallen below 2 volts, the
battery cannot be recharged with this unit.
– Make sure output connection are secured.
– Check correct polarity connections.
– If the maintainer does not detect battery voltage, the unit will
not run.
CARE AND MAINTENANCE
With proper care and minimal maintenance, this unit will provide years of dependable service. For
maximum performance, manufacturer recommends:
• After each use, clean the battery charger clamps — be sure to remove any battery fluid that will
cause corrosion of the clamps.
• Clean the outside case of the charger with a soft cloth and, if necessary, mild soap solution.
• Do not allow liquid to enter the charger. Do not operate when charger is wet.
• Keep the charger cords loosely coiled during storage to prevent damage to the cords.
CAUTION: TO REDUCE THE RISK OF PERSONAL INJURY OR PROPERTY DAMAGE:
BM3B_ManualENFRSP_040111.indd 8-9
4/1/2011 3:37:11 PM
