Black & Decker BL188, Original Instructions Manual

Page: 9 / 92

9
ENGLISH (Original instructions)
LED work light
When drill is activated by pulling the trigger switch (1), the
integrated LED work light (8)will automatically illuminate the
work area.
Note: The work light is for lighting the immediate work surface
and is not intended to be used as a flashlight.
Bit tip storage
A bit storage slot (9) is built into the base of the tool.
Troubleshooting
Problem Possible cause Possible solution
Unit will not start. Battery pack not
installed properly.
Battery pack not
charged.
Check battery pack
installation.
Check battery pack charg-
ing requirements
Unit starts immedi-
ately upon inserting
battery
The switch has
been left in the “on”
position.
The switch must be
moved to “off” to prevent
the tool from immediately
starting when battery is
inserted.
Battery pack will not
charge.
Battery pack not
inserted into charger.
Charger not plugged
in.
Surrounding air
temperature too hot or
too cold.
Insert battery pack into
charger until LED lights.
Plug charger into a work-
ing outlet.
Move charger and battery
pack to a surrounding air
temperature of above 40
degrees F (45ºC) or below
105 degrees F (+40.5ºC)
Unit shuts off
abruptly.
Battery pack has
reached its maximum
thermal limit.
Out of charge. (To
maximize the life of
the battery pack it is
designed to shutoff
abruptly when the
charge is depleted
Allow battery pack to cool
down.
Place on charger
and allow to charge.
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
u
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
u
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
u
Regularly open the chuck and tap it to remove any dust
from the interior.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed
of with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical data
BL188 H2
Voltage V
DC
18V
No-load speed Min
-1
0-450 / 0-1800
Max. torque Nm 52
Chuck capacity mm 13
Max Drilling capacity
Steel/wood mm 13/35
Weight kg 1.08 (1.46 with
battery)
Charger 90590289 90634972
Input voltage V
AC
100- 240 220 - 240
Output voltage V
DC
8 - 20 8 - 20
Current mA 400 1000
Approx. charge time Hrs 3 - 5 1.5 - 2
Battery BL1518 BL2018 BL4018
Voltage V
DC
18 18 18
Capacity Ah 1.5 2.0 4.0
Type Li-Ion Li-Ion Li-Ion
Level of sound pressure according to EN 62841:
Sound pressure (L
pA
) 87.5 dB(A), uncertainty (K) 5 dB(A)
Sound power (L
WA
) 98.5 dB(A), uncertainty (K) 5 dB(A)
Vibration total values (triax vector sum) according to EN 62841:
Drilling into metal (a
h.D
) 1.9 m/s
2
, uncertainty (K) 1.5 m/s
2
Impact drilling into concrete (a
h.ID
) 10.4 m/s
2
, uncertainty (K) 1.5 m/s
2