Black & Decker BCD001, Original Instructions Manual

Page: 7 / 100

● Do not charge damaged batteries.
● Under extreme conditions, battery leakage may occur.
When you notice liquid on the batteries carefully wipe the
liquid off using a cloth. Avoid skin contact.
● In case of skin or eye contact, follow the instructions
below.
@
Warning! The battery fluid may cause personal
injury or damage to property. In case of skin contact,
immediately rinse with water. If redness, pain or
irritation occurs seek medical attention. In case of
eye contact, rinse immediately with clean water and
seek medical attention.
Chargers
Your charger has been designed for a specific voltage. Always
check that the mains voltage corresponds to the voltage on
the rating plate.
@
Warning! Never attempt to replace the charger unit
with a regular mains plug.
● Use your charger only to charge the battery in the tool with
which it was supplied. Other batteries could burst, causing
personal injury and damage.
● Never attempt to charge non-rechargeable batteries.
● If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Service Centre in order to
avoid a hazard.
● Have defective cords replaced immediately.
● Do not expose the charger to water.
● Do not open the charger.
● Do not probe the charger.
● The appliance/tool/battery must be placed in a well
ventilated area when charging.
$
The charger is intended for indoor use only.
Electrical safety
#
This charger is double insulated; therefore no
earth wire is required. Always check that the
power supply corresponds to the voltage on the
rating plate.
● If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Forward/reverse slider
3. Torque adjustment collar
4. Keyless chuck
5. LED work light
6. Battery
7. Battery release button
Assembly
Use
@
Warning! Let the tool work at its own pace. Do not
overload.
Charging the battery (fig. A, B)
The battery needs to be charged before first use and
whenever it fails to produce sufficient power on jobs that were
easily done before. The battery may become warm while
charging; this is normal and does not indicate a problem.
@
Warning! Do not charge the battery at ambient
temperatures below 10 °C or above 40 °C.
Recommended charging temperature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the
charger will begin to charge automatically when the cell
temperature warms up or cools down.
● Plug the charger (8) into any standard 230 Volts 50 Hz
electrical outlet.
● Slide the battery pack (6) into the charger as shown in
figure A, B.
The LED (8a) will flash indicating that the battery is being
charged.
The completion of charge is indicated by the LED (8a)
remaining on continuously. The pack is fully charged and may
be used at this time or left on the charger.
@
Warning! fire Hazard. When removing the charger
from the battery, be sure to unplug the charger
from the outlet first, then remove the battery from
the charger.
Charger diagnostics
This charger is designed to detect certain problems that can
arise with the battery packs or the power source. Problems
are indicated by one LED flashing in different patterns.
Bad battery
The charger can detect a weak or damaged battery. The LED
flashes in the pattern indicated on the label. If you see this bad
battery blink pattern, do not continue to charge the battery.
Return it to a service center or a collection site for ecycling.
Hot/cold pack delay
When the charger detects a battery that is excessively hot or
excessively cold, it automatically starts a Hot/Cold Pack Delay,
suspending charging until the battery has normalized. After
this happens, the charger automatically switches to the Pack
Charging mode. This feature ensures maximum battery life.
The light flashes in the pattern indicated on the label.
Leaving the battery in the charger
The charger and battery pack can be left connected with
the LED glowing indefinitely. The charger will keep the
battery pack fresh and fully charged.
7
ENGLISH (Original instructions)