Automatic Lift Fryer
Operation
15
3. The digital timer has a STIR OIL function that operates in one of four reconfigurable modes. If the
timer needs to be reconfigured, follow step a. If the timer does not need to be reconfigured, follow
step b.
a. Press and hold the ALARM button and at the same time place the
FILTER/OFF/FRY
switch
in the
FRY
position. The display will show the word “STIR” until the ALARM button is
released. When the button is release the display will show the current configuration mode. To
change this mode select the timer key that represents the mode you want. Refer to the table
below:
KEY DISPLAY
MODE
DESCRIPTION
A -AL-
New or unchanged timer. Alarm sounds at the end of the internal 6
minute countdown.
B -OFF
Defeats the STIR OIL function. Timer operates as if it had no STIR OIL
function.
C
PrES
STIR OIL function for all Pressure Fryers.
D
LiFT
STIR OIL function for all Autolift Fryers.
The display will now show the selected mode. Proceed to step c.
b. Once the fryer is filled with shortening, place the
FILTER/OFF/FRY
switch in the
FRY
position.
c. Unless the STIR OIL function is operating in the –OFF mode, the digital timer activates a
STIR OIL function and begins an internal six minute countdown (not displayed). At the end of
the internal countdown, the display shows the words “STIR” then “OIL” in .5 second intervals
and the alarm sounds. Depress the
ALARM
button and stir the shortening freely while it is
heating.
IMPORTANT
!
Before the first cooking operation each day, stir the shortening freely while it is
heating to provide a balanced shortening temperature for excellent results with the first
cooking. Failure to do this can result in a crusty skin on the product surface with an
undercooked product internally. In addition, in some cases, failure to stir the shortening while
it is initially heating may cause the HI-LIMIT safety device to disable the power due to a false
overtemperature condition.
4. Set the thermostat to the desired cook temperature. The temperature light will go on. When the
temperature is reached, the light will go off. The light will continue to cycle on and off as the fryer
maintains the set temperature.
5. Raise the basket to the top position by depressing the basket switch to the
UP
position.
6. Press and hold the
TIME SELECT
arrow buttons on the digital timer until the desired cook time is
displayed or recall a preset time by quickly pressing the appropriate preset button.
7. The shortening will heat and begin to reach the fill mark inside the pot. Add more shortening as
required to reach the fill mark.
Summary of Contents for ALF-F
