BIXOLON SRP-350III Command Manual Download

Page: 99 / 119

SRP-350/352III

Rev. 1.01

BIXOLON

- 99 -

GS V

Function:

Select cut mode and cut paper

Code:

①

ASCII

Hex

Decimal

②

ASCII

Hex

Decimal

Range:

①

m=0, 1, 48, 49

②

m=65, 66, 0

≤ n ≤ 255

Default:

None

Description:

This command cuts paper in the specified mode as follows.

Function

①

0,48

Executes a partial cut (one point left uncut)

1,49

②

Feeds paper to (cutting po n × vertical motion unit) and executes a partial cut(one point left uncut)

Remarks:

For

①

■

If an auto cutter is not provided, this command is ignored command is executed.

For

②

■

When n = 0, the printer feeds the paper to the cutting position and cuts it.

■

If an auto cutter is not provided, the printer only feeds the paper for specified amount.

■

Vertical motion unit is used for calculating a paper feed amount.

■

Cutting mode is changed only by setting MSW5-1.

Differences:

None

Summary of Contents for SRP-350III
























































































































Search results

Summary of Contents for SRP-350III

Reviews:

Related manuals for SRP-350III

Brands by name

Popular brands

BIXOLON SRP-350III, Command Manual

Search results

Summary of Contents for SRP-350III

Reviews:

Related manuals for SRP-350III

Brands by name

Popular brands