BIXOLON SRP-350III Command Manual Download

Page: 20 / 119

SRP-350/352III

Rev. 1.01

BIXOLON

- 20 -

ESC &

Function:

Define user-defined character set

Code:

ASCII

ESC

y c1 c2 [x1 d1 ... d(y

ⅹ

x1)]... [xk d1 ... d(y

ⅹ

xk)]

Hex

y c1 c2 [x1 d1 ... d(y

ⅹ

x1)]... [xk d1 ... d(y

ⅹ

xk)]

Decimal

y c1 c2 [x1 d1 ... d(y

ⅹ

x1)]... [xk d1 ... d(y

ⅹ

xk)]

Range:

y = 3
32 ≤ c1 ≤ c2 ≤ 126
0 ≤ x ≤ 12 (Font A)
0 ≤ x ≤ 9 (Font B)
0 ≤ d ≤ 255
k = c2

– c1 + 1

Default:

None

Description:

■

This command defines user-defined characters for character codes in a designated range from the start character
code, c1 to the end character code, c2.

•

y denotes the number of bytes in the vertical direction, x the number of dots in the horizontal direction, and d the

dot data for the user-defined characters.

Remarks:

■

Alphanumeric characters (20H (decimal 32) to 7EH (decimal 126)) are definable.

■

Once user defined characters are defined, they remain available until they are redefined; ESC ? or ESC @ is

executed; the printer is reset.

■

The following shows the relationship between the definition data and printing result with downloaded character

consisting of 9x7 dots.

d11

d13

MSB

LSB

d10

d12

d14

MSB

LSB

Differences:

None

Summary of Contents for SRP-350III
























































































































Search results

Summary of Contents for SRP-350III

Reviews:

Related manuals for SRP-350III

Brands by name

Popular brands

BIXOLON SRP-350III, Command Manual

Search results

Summary of Contents for SRP-350III

Reviews:

Related manuals for SRP-350III

Brands by name

Popular brands