BIXOLON SPP-L310 Installation Manual Download Page 2

Page: 2 / 20

◈

MSR Usage (Only SPP-R310)

1. Insert the card as shown in the

image and swipe in the direction of
the arrow. (can be done in both
directions)

※

Note

If the card does not register, first
check to see if it is properly aligned.
When swiping the card, the
recommended swiping speed is 100 ~
1200 mm/sec.

◈

Self-test

Run the self-test when first setting the printer or when encountering a problem, and check the
following.

• Control Circuit, Mechanisms, Print Quality, ROM Version, and Memory Switch Settings

If no issue is found with the printer after running the self-test, examine the other devices or
peripherals and software. This function is independent of such other devices and software.

• Self-Test Instructions

1) Turn the printer power off and close the printer paper cover.
2) Pressing the paper feed button and power button simultaneously turns the printer on.
3) After printing begins, please release the two buttons.
4) To add a printout of the ASCII pattern, press the paper feed button once more.
5) After the ASCII pattern is printed out, the self-test is automatically terminated.

◈

Product Specifications

Item

Description

SPP-R310

SPP-L310

Printing

Printing Method

Thermal printing

Print Speed

Receipt paper: 100 mm/s
Linerless paper: 80 mm/s

Label paper: 127 mm/s
Linerless paper: 80 mm/s

Resolution 203

DPI

Emulation

BXL/POS

SLCS, BPL-Z™, BPL-C™

Sensor

Paper End Sensor,
Paper Cover Open Sensor,
Black Mark Sensor(Optional)

Gap Sensor,
Paper Cover Open Sensor,
Black Mark Sensor

Cutter Type

Tear-bar

Paper

Paper Type

Thermal Paper

Outer Diameter

of Paper Roll

Reciept Paper: Max. Ø50 mm (1.97”)
Label Paper: Max. Ø49 mm (1.93”)
Linerless Paper: Max. Ø49 mm (1.93”)

Width

79.5 ± 0.5 mm (3.13” ± 0.2”)

Thickness

Reciept Paper: 0.07 ± 0.005 mm
Label Paper: 0.07 ± 0.15 mm
Linerless Paper: 0.08 ± 0.01mm

Interface

R310
- USB, SERIAL
- Bluetooth Class2 V3.0

+EDR,

- Wireless LAN 802.11 b/g/n

R310plus
- USB, SERIAL
- Bluetooth 4.1(Classic/LE)
- W LAN 802.11 a/b/g/n

USB, SERIAL
Bluetooth4.1(Classic/LE)
WLAN 802.11 a/b/g/n

※

Note

1) This equipment is indooruse and all the communication hiring are limited to inside of the

building.

2) The switch is the disconnecting device. Turn off switch from any hazard.

◈

Label Printing Function

1. Label Function Setting

Label paper and black mark paper available at the label mode.

• Setting Operations

1) Turn on the printer power.
2) Open the paper cover and press and hold down the paper feed button for longer than two

seconds.

3) After the buzzer tone is emitted, insert paper and close the cover.
4) Repeat the steps above to return to receipt mode.

• Setting Via Memory Switch

1) Please refer to the memory switch changing section of the Commands Manual.

2. Auto Calibration Function

The label printing function requires the recognition of label paper gaps and black mark
paper black bar in order to print.
If label paper gaps are not properly recognized, use the auto calibration function.

• Auto Calibration Instructions (Only SPP-R310)

1) Turn the printer power off while in label print mode.
2) Press and hold down the paper feed button and then press the power button.
3) After the following printout is outputted, press the power button to perform auto

calibration.

Select the mode

Auto Calibration: Power Button

Self Test: Feed Button

4) Three pages of label paper are outputted when performing auto calibration.

◈

Peripherals Connection

1. Bluetooth & Wireless LAN Connection

1) The printer can be connected to devices

equipped with Bluetooth communication
capacity (PDAs, PCs, etc.).

2) Use the Bluetooth connection function

supported by the device to connect to the
printer.

3) The printer can be connected to other

stations, such as PDAs and PCs supporting
wireless LAN communication in Ad-hoc
mode and AP in Infrastructure mode.

※

Note

Refer to the Bluetooth Wireless LAN Manual for detailed information on its connection.
You can check the Bluetooth environment (authentication, encryption, connection mode) and
the wireless LAN environment (IP, SSID, authentication, encryption) via the self-test page.

2. Interface Cable Connection

1) Open the Interface Cap
2) Connect the interface cable (optional) to the

cable connector of the printer.

◈

Printer Cleaning

If the interior of the printer is dusty, print quality can decline.
In such a case, follow the instructions below to clean the printer.
• Make sure to turn the printer power off prior to cleaning.
• As the print head gets very hot during printing, if intending to clean the print head, turn the

printer power off and wait approximately 10 minute before commencement.

• When cleaning the print head, take care not to touch the heated portion of the print head.

→

The print head is susceptible to damage from static electricity, etc.

• Take care not to allow the print head to become scratched and/or damaged in any way.

1) Open the paper cover and remove any paper that may be present.

Use the cleaning pen to clean the printer head in a direction from the center to the
outside.

2) Wipe the print head with a cleaning pen.
3) Remove paper dust from the paper detection sensor using the cleaning pen.
4) Do not use the printer for 10 minutes after cleaning the printer head until the cleaning

agent of the cleaning pen has completely evaporated and dried.

5) Insert the paper and then close the printer’s cover.

◈

Certification

This marking shown on the product or its literature, indicates that it should not be
disposed of with other household wastes at the end of its working life. To prevent
possible harm to the environment or people from uncontrolled waste disposal, please
separate this from other types of wastes and recycle it responsibly to promote the
sustainable reuse of material resources. Household users should contact either the retailer
where they purchased this product, or their local government office, for details of where
and how they can take this item for environmentally safe recycling. Business users should
contact their supplier and check the terms and conditions of the purchase contract. This
product should not be mixed with other commercial wastes for disposal.

The following Bluetooth mark and QD ID D029148 is only applicable to models with the
Bluetooth SIG qualification.

☎

BIXOLON Co., Ltd.

●

Website

http://www.bixolon.com

●

Korea Headquarters

(Add) 7~8F, (Sampyeong-dong), 20, Pangyoyeok-ro241beon-gil,

Bundang-gu, Seongnam-si, Gyeonggi-do, 13494, Korea (ROK)

(Tel.) +82-31-218-5500

●

U.S. Office