10
DS901423-001
DS901423-001
11
CODE
: user
code.
Set a number from 0 to 127 according to the following rules:
No two apartments in the system must have the same user code.
Indoor stations in parallel in the same apartment must have the same user code.
User codes be consecutive in the same column must.
Use the CODE dip switches from 2 to 8 (2= most signifi cant bit - 8= least signifi cant bit) to set the required
code. Dip switch 1 must be OFF.
INT
: apartment
station
code.
Set a number from 0 to 3 according to the following rules:
The indoor station code must be 0 if there is only one station in the apartment.
Up to 4 apartment stations can be connected in parallel using the same user code and different indoor station
codes.
The indoor station code is used to identify the single stations of the same user. This means that intercom calls
can be address to the single user in the same apartment. All the users indoor stations will ring at the same time
in the event of intercom calls to different apartments, door unit calls and fl oor calls. Consider the following:
Extension 0 rings immediately when a call is received. Extensions 1, 2 and 3 will ring in sequence after each
other.
Apartment station 0 will enable monitor switch-on if the call is from a video calling station.
The
button
B
can be pressed on any other apartment station of the same user to switch on the other video
door phone (“video switching” function).
LINE TERMINAL SETTINGS
Line termination
OFF
ON
A jumper for fi tting a line terminal is present on indoor stations bracket. Activate the termination in all end-
of-line devices from which no other section starts from the BUS OUT terminals:
Termination
ON
Termination
OFF
BUS OUT
BUS IN
BUS 1
BUS 3
BUS 4
BUS 2
AV1001/03
BUS OUT
BUS IN
Termination
ON
BUS 1
BUS 3
BUS 4
BUS 2
Termination
ON
BUS OUT
BUS IN
AV1001/03
•
•
•
•
•
•
PERFORMANCE
CALL RECEPTION AND VIDEO SHIFTING FUNCTION
The user’s apartment station will ring with the programmed tone when a call is received according to the
source:
From main door unit
From secondary door unit
Intercom call
Floor calls
From switchboard
The electric lock of the door unit can be operated when a video door unit or door unit call is received without
needing to establish a conversation.
If there are several apartment stations in parallel, the extensions will ring in sequence. The user’s extension 0
will also switch the video door phone if the call comes from a video door phone station. In this case, during
the call pick-up time (60s from the call), the video door phones of the other extensions can be switched on
by pressing the auto-on button
B
(video switching function) until one of the called user’s video door phones
picks up.
If the picture is already displayed, pressing button
B
will show the stream of the surveillance cameras of the
calling station only in cycle.
The picture of the main camera will appear only on the apartment station that picked up after picking the call
up.
The camera picture will therefore be normally shown on only one apartment station at a time.
AUTO-ON FUNCTION
Press
B
to automatically switch the door station on when the apartment station is in stand-by and on-hook.
Press the button again to cyclically display the picture from the surveillance cameras installed in the main door
units in the system and the secondary door unit of the column to which the device belongs.
Pick up the handset to establish audio and video communication with the selected door unit. The door of the
selected door unit can be opened at any time.
INTERCOM CALL FORWARDING
After programming the button for the intercom function, pickup the handset and press the button.
The following cases can occur according to the calling indoor station state:
Indoor station free: the calling indoor station will output a confi rmation tone (2 beeps) and the called
indoor station will ring. Communication is established when the called user picks up.
Indoor station busy: the indoor station outputs a warning tone (4 beeps in rapid sequence). Hang up and
try again later.
FLOOR CALL FUNCTION
The indoor station is equipped with a pair of terminals (P) for connecting the fl oor call button. The indoor
station will ring with the set tone for 3s when the button is pressed. Connect this button to indoor station only
if there are several indoor stations in parallel. Indoor station 0 will ring immediately. The apartment stations
will ring in sequence.
SUPPLEMENTARY RINGER
The apartment stations are provided with a pair of terminals (S+, S-) for connecting a supplementary ringer or
relay. This ringer is controlled when any call tone is generated.
•
•
•
•
•
•
•
