manualshive.com logo in svg

BitaTek IT-6000 Series, User Manual, Page: 67 / 72

Share
Download
BitaTek IT-6000 Series User Manual Download Page 67

67  

SNMP 

SNMP (Simple Network Management Protocol) is the standard 
protocol for managing devices on a network. The Firmware 
Management Utility (FMU) makes use of SNMP to send and 
receive configuration information to the terminals. Since the 
networked terminals are constantly running SNMP, this allows 
FMU to interface with the terminal at any time, without requiring 
user intervention on the terminal. 
With SNMP running on the terminal, other SNMP based network 
management tools such as HP Openview® and CastleRock 
SNMPpc® may also be used to interface with the terminals. To 
support this capability, We have released the Management 
Information Base (MIB) for the Windows based terminals. The MIB 
is used by the management tools to allow them to better support 
the configuration values provided on the terminals, such as 
scanner controls and terminal type information. 

 

Installing & Setting Up Microsoft® ActiveSync 

This section provides instructions on setting up the Host PC so that 
the PC can communicate with the device. 

 

Microsoft® ActiveSync 

Microsoft® ActiveSync is a file transfer tool to synchronize the files 
on a PC with the files on your device. The device comes from the 
factory with ActiveSync loaded. If you have ActiveSync already 
installed on your PC, make sure that you have v3.7 or higher. 
To install Microsoft® ActiveSync, complete the following steps on 
the PC: 
1.

 

Go to the Microsoft® WindowsCE .Net website and download 
the most current version of ActiveSync: 

 

http://www.microsoft.com/mobile/pocketpc/downloads/

. 

 
2.

 

Install the most current version of Microsoft® ActiveSync (v3.7 
or higher) on the host PC. 

3.

 

Click the Next button to continue the installation. Click Cancel 

Summary of Contents for IT-6000 Series









































































Reviews:

No comments