Problem
Possible causes
Remedies
Reduced
spray OR
no spray
Bladder may be empty.
Turn switch power off; refill bladder
with clean hand hot tap water.
The lint screen may be clogged.
Clean out lint screen.
Tank-in Tank may not be seated
properly.
Turn power switch OFF; remove tank
and reseat tank.
Pump may have lost prime.
Turn power switch OFF; after 1 minute
turn ON and depress spray trigger.
The pump belt may be broken
Turn power Switch OFF and unplug machine from
the outlet. To check if a pump belt has broken, you
will need a flat head screwdriver. Insert the blade
end into the lower slot of the belt access door to
release the lower snap. If necessary, insert the blade
end into the upper slot to release the upper snap.
Examine the belt for breakage. You should be able
to see the pump belt looped around the motor shaft.
If it is broken or missing, please refer to Replacement
Parts on page 19 before calling BISSELL Consumer
Care. Complete installation instructions will accom-
pany the replacement belt.
DirtLifter
PowerBrush
does not turn
The brush belt or pump belt may
be broken.
Turn power switch OFF and unplug machine
from the outlet. To check if a brush or pump
belt has broken, you will need a flat head screw-
driver. Insert the blade end into the lower slot of
the belt access door to release the lower snap.
If necessary, insert the blade end into the upper
slot to release the upper snap. Examine the belt
for breakage. If broken refer to pages 14-15
OXY
PowerWash
is not picking
up solution
and water
ReadyTools Dial may be at the
wrong setting for the cleaning job.
Set ReadyTools dial to either Tools or
Floor Cleaning.
Nozzle window may not be
properly attached.
Make sure the two tabs on the back of
the floor nozzle window are inserted
through the mating slots in the main
housing. Re-install if necessary.
Tank-in-Tank lid is not properly
installed.
Re-install lid; refer to the Operation
section, page 6.
Tank-in-Tank is not properly
seated.
Tank-in-Tank must be firmly seated
to function. Remove and reseat
Tank-in-Tank.
Poor tool position
(hand held attachments only).
Adjust angle; apply more
downward pressure.
Tank-in-Tank has picked up
maximum dirty water.
Empty Tank-in-Tank and refill, refer to
the Operation section, page 7.
Replacement Parts
These items are available for purchase as accessories for your BISSELL vacuum:
To purchase visit www.BISSELL.com. *Not all parts are included with every model
PART # PART NAME
PART #
PART NAME
214-4025
Handle Assembly
215-9155
Tough Stain Brush
PUSH
015-9043
Tank Assembly Complete
015-4439
Tank Lid Assembly
015-9041
Tank Bottom
213-0213
Baffle with Red Float
160-0816
Floor Nozzle Window
203-6651
3" Tough Stain Tool
203-6653
4” Upholstery Tool
214-9131
Bare Floor Tool
203-6652
TurboBrush
BR
US
H
SU
CT
ION
210-4052
Window Gasket
215-0628
Replacement Pump Belt
(with instructions)
015-0621
Replacement Brush Belt
(with instructions)
213-3501
Lint Screen
1134-E
1 L Oxygen Boost
203-7240
Oxy Power Tool
1089-E
1.5 L 2X Wash & Protect
Professional Formula w/
Scotchgard™ Protector
210-3040
Mesh Tool Storage Bag
1086-E
1.5 L 2X Wash & Protect
Stain & Odour Formula w/
Scotchgard™ Protector
1087-E
1.5 L 2X Wash & Protect Pet
Stain & Odour Formula w/
Scotchgard™ Protector
1147-E
651 mL Tough Stain Precleaner
1144-E
1 L 2X Wash & Shine Hard Floor
Solutions
www.BISSELL.com
11
