background image

16

w w w . b i s s e l l . c o m  

8 0 0 . 2 3 7 . 7 6 9 1

 6

w w w . b i s s e l l . c o m  

8 0 0 . 2 3 7 . 7 6 9 1

Cleaning with your Auto Care

1.

  Hold the tool approximately 1” above the 

soiled surface. Press the spray trigger to 

apply the cleaning solution to the soiled area.

2.

  Using the brush on the tool, gently scrub the 

area to be cleaned.

3.

  For thorough cleaning, spray additional 

solution while the brush and suction are in 

contact with the surface.

4.

  Apply downward pressure on the tool and 

pull it toward you. The suction will remove 

the dirt and cleaning solution. Continue until 

no more dirt can be removed.

5.

  As a final step, use “drying strokes” (by not 

pressing the spray trigger) to remove as 

much liquid/moisture as possible. Repeat 

this step as often as necessary.

After cleaning

1.

  Unplug power cord from outlet.

Note: If a significant amount of Little Green  

formula/water remains, it is all right to leave it in 

the clean/solution tank for your next cleaning task.

2.

  Empty and rinse the dirty/collection tank after 

each use, OR when dirty water reaches the 

indicated maximum fill line. To remove the 

tank, lift up the dirty/collection tank release 

latch and remove the tank from the unit.

3.

  Disconnect the cleaning tool from the spray 

trigger by pushing down on button lock and 

pulling straight off.  

(Do NOT twist tool to remove it)

4.

  Once removed from the spray trigger, clean 

tool by rinsing under running water.

5.

  Check spray nozzle for accumulated dirt or 

debris. If necessary, clean with soft bristle brush.

Machine storage 

1.

  Wipe all surfaces with a soft cloth.

2.

  Wrap power cord around the cord wrap on 

the back of the Auto Care.

3.

  Wrap vacuum flex hose around the base of 

the unit and secure the spray trigger.

4.

  Store unit in protected, dry area, at room  

temperature (40º to 110ºF).

O

peration

M

aintenance and care

IMPORTANT:

   

Check the manufacturer’s tag before 

cleaning upholstery. “W” or “WS” on the 

tag means you can use your Auto Care. If 

tag is coded with an “S” (with diagonal 

strike-through), or says “Dry Clean Only,” 

do not proceed. If manufacturer’s tag is 

missing or not coded, check with your 

furniture dealer.

Tip:

Deep cleaning 

stairs and 

high-traffic 

areas on a 

regular basis 

can prolong 

carpet life

.

Tip:

Check upholstery 

stuffing before 

cleaning. Colored 

stuffing may 

bleed through 

the fabric when it 

becomes wet.

Tip:

Before turning off the Auto Care, 

vacuum up clean water to thoroughly 

rinse out the interior of the vacuum  

flex hose. Then, lift the cleaning tool 

and point it upwards to drain any 

remaining water into the dirty/ 

collection tank.

WARNING:   

Keep spray away from face. 

Failure to do so may result in 

personal injury.

Tank Release  
Latch

Summary of Contents for LittleGreen Proheat 1425 Series









Reviews: