background image

 5

w w w . b i s s e l l . c o m  

8 0 0 . 2 3 7 . 7 6 9 1

O

peration

Getting ready

1.

  To fill the clean/solution tank. 

A.

  Remove the tank by lifting it straight up 

and then away from the unit.

B.

  Unscrew the black cap at the bottom of the 

clean/solution tank and remove bottle insert.

C.

  Add BISSELL Little Green formula to the 

FORMULA fill line (8 oz.) on the clean/solution 

tank. Fill the clean/solution tank with hot (NOT 

boiling) tap water to the WATER fill line. Replace 

the bottle insert and tighten the black cap.

D.

  Replace the clean/solution tank by lining up 

the vertical guides on the left side of the unit 

with the indentations on the clean/solution 

tank and gently sliding it down into position.

2.

  Release vacuum flex hose by twisting the 

bracket latch clockwise. Unwrap vacuum flex 

hose completely from around unit.

3.

  Attach the tough stain brush tool to the spray 

trigger unit by pressing tool onto spray trigger 

firmly until the button lock snaps into hole. 

Make certain the tool is securely attached.

4.

  Twist the Quick Release cord wrap clockwise 

to unwrap the power cord completely from 

onboard cord storage and plug into 120 Volt 

grounded outlet, as described in Important 

Safety Instructions, page 3. 

The heat indicator 

light will take 30 seconds to illuminate.

5.

  Press and hold spray trigger—spray will  

start in a few seconds. Raise the tool slightly 

to check for spray. 

Pre-treating

Cleaning effectiveness will be enhanced if you 

pre-treat heavily stained or highly-soiled areas. 

Here’s how to do it:
1.

  Hold the cleaning tool just above the surface 

of the carpet or upholstery to be cleaned. 

Press the trigger to release a spray of cleaning 

solution directly onto the soiled area.

2.

  Wait 3-5 minutes before cleaning.

Collection/ 
Dirty Tank 

PCV free

Tank Release 
Latch

WARNING:

   

Do not use this product while on any type of ladder. 

Do not place the product in a place where it will be 

stepped on or kicked while in use. Do not place the 

product on an elevated surface where it may be 

pulled off the surface while in use. 

WARNING:

   

Do not use an extension cord with this 

product. The use of an extension cord may 

result in a severe electrical shock, particu-

larly if the extension cord does not have 

an electrical rating higher than that of the 

product, OR if the extension cord does not 

have a three-prong grounding plug  

and if the extension cord is not plugged 

into a circuit box with a ground fault circuit 

interrupter. Safety precautions such as 

keeping all connections off the ground and 

dry will not eliminate the danger.

WARNING:

   

Use only BISSELL Little Green formula 

in your cleaner. Use of cleaning  

formulas which contain lemon or 

pine oil may damage this appliance 

and void the warranty. Chemical 

spot cleaners or solvent-based soil 

removers also should not be used. 

These products may react with the 

plastic materials used in your cleaner, 

causing cracking or pitting.

1A

1B

1C

1D

3

2

4

5

Water

Formula

Summary of Contents for LittleGreen Proheat 1425 Series









Reviews: