background image

Carpet cleaning

1. 

Plug the deep cleaner into a proper outlet. 

Turn the power ON by pressing the red power 

switch on the back of the unit with your foot.

2. 

With your foot, press the gray handle  

release lever located on the back of unit  

below water tank.

3. 

While pressing the spray trigger, make one 

slow forward wet pass and another back. Let  

the BISSELL 2X deep cleaning formula and 

DirtLifter PowerBrush do the work for you. 

Caution: Do not overwet.
4. 

Release the spray trigger and make one  

slow forward and backward pass over the  

same area to remove any residual dirty water 

and aid in drying.

5. 

Repeat cleaning passes until solution being 

pulled up appears clean. Continue passes  

without pressing the spray trigger until you  

can’t see any more water being suctioned up.

Empty the 2-in-1 water tank/clean removable nozzle

1. 

Turn power switch OFF. Remove the 2-in-1 

water tank from the base using the tank carry 

handle. Carry the tank like a bucket to a utility 

sink or outside where you will dispose of the 

collection water. Remove the top of the tank by 

rotating the handle forward to unlatch lid and 

lifting lid off tank.

2. 

Empty collection water from bottom of tank.

3. 

After each use, remove and rinse the lint 

screen located on the tank lid. 

4. 

If nozzle needs to be cleaned, remove by 

grasping handle at the top and pulling forward. 

Clean removable nozzle by rinsing under  

running water.  

5. 

When finished, replace nozzle by slightly  

raising front of machine to line up slots on the 

base with the hooks on nozzle. Attach at base 

first and then click nozzle into place. 

NOTE: If nozzle is not attached properly loss  

of suction will occur.

6. 

To continue carpet cleaning, refer back to “Fill 

the 2-in-1 water tank” instructions on page 8 and 

“Carpet Cleaning” instructions above.
If cleaning is complete, refer to the “Maintenance 

and care” section on page 12.

Operations

   

   www.BISSELL.com

9

Handle Release

2.

3.

1.

5.

Lint Screen

Power Switch

4.

CAUTION

ROTATING BRUSH INSIDE-TO AVOID THE RISK OF 

INJURY-UNPLUG BEFORE REMOVING

Summary of Contents for CLEANVIEW 44L6 SERIES

















Reviews: