background image

1

3

4

5

6

Wall Mounting  

(Using ED wall duct and EG external grille)

2

3

Remove the two retaining screws under
decorative cover and then pull bottom of 
decorative cover while lifting. 

Cut the duct to width of the plasterboard
or tiled wall with slight fall to exterior.
(Make provisions for cable).

Fill in any gaps with mortar or foam and
make good internal and external walls.
Make sure that ducting remains circular
and screw holes are horizontal.

Using No 8 screws, secure fan body to
ducting. The electrical cable passes through
as appropriate. Wire fan (See wiring details).
Ensure metal retaining bracket connecting
holes are positioned at the bottom.

Fine Adjustments

If after installation the fan is not
level, the front grille can be
turned upto 5º clockwise or 5º
anti-clockwise to correct this.

8

7

Replace decorative cover by hooking onto the
top of grille on the main body then push bottom
of cover home. Align screw holes with metal
retaining bracket and gently tighten retaining
screws at bottom of cover, ensuring no wires are
trapped.

Screw the protective wall grille over the
external duct opening.

To Clean or Service Fan

WARNING: 
Isolate electricity supply before removing or replacing jumper switch.

Remove jumper switch if 10 L/S constant airflow rate is required.

Replace jumper switch if 5 L/S constant airflow rate is required.*

* Factory set at 5 L/S.

Constant Airflow Settings

WARNING: 
Always isolate fan from mains supply before cleaning. 
Do not use solvents to clean this fan.

Remove the two retaining screws under decorative cover and
then pull bottom of cover while lifting. Pull bottom of internal
grille while lifting (as shown in figures 1 and 2). 

The fan may now be cleaned using a  brush, cotton bud or 
damp cloth. 

DO NOT IMMERSE IN WATER.

Keep points 1 (sensor) and 2 
(impeller) clean for best 
performance.

After cleaning replace internal 
grille and decorative cover. 
Align screw holes with metal 
retaining bracket and gently 
tighten screws at bottom of cover 
(as shown in figures 6 and 7).

To Clean the Serenity Grille

WARNING: 
Always isolate fan from mains supply before cleaning. 
Do not use solvents or an abrasive cloth to clean the grille.

Wiring Details

Use a soft damp cloth to wipe clean surfaces.

Use a soft dry cloth to buff surfaces.

Strip cable to correct lengths as shown 
in diagram 1.b. 

Insert cable through cable entry point, 
then clamp cable using the cable clamp.

Use the cable guides to retain the cable 
wires, then push the wires into the 
terminal block until cable comes to a 
dead stop. (Diagram 1.a)

Peel open the terminal cover, so that 
terminal screws are visible, then tighten 
screws and replace terminal cover,
making sure that cover is fully replaced.

Strip cable to correct lengths as shown 
in diagram 2.b. 

Break open cable entry point then insert 
cable.

Push the wires into the terminal block 
until cable comes to a dead stop. 
(Diagram 2.a)

Peel open the terminal cover, so that 
terminal screws are visible, then tighten 
screws and replace terminal cover,
making sure that cover is fully replaced.

1

2

1.b

2.b

1.a

2.a

Installation Method 1 - For Long Cable

Installation Method 2 - For Short Cable

Replace internal grille by hooking the top of
grille onto main body then push bottom of grille
home. 

Pull bottom of internal grille while lifting. 

2

3

4

9

5

8

Ceiling Mounting

Cut an opening through the ceiling for the
fan and electrical cable. Ensure ceiling surface
is smooth, clean and dry prior to fixing fan.

Secure to ceiling using suitable fixing method
then Wire fan (See wiring details). Ensure 
fixing holes on metal retaining bracket are
accessible after installation.

Place flexible ducting over the spigot of the
fan. Fit ducting to spigot using ties. Replace
front grille.

Diagram depicting typical installation ducted
through roof soffit.

Diagram depicting typical installation ducted
through roof to external wall.

Fine Adjustments

If after installation the fan is not
level, the front grille can be
turned upto 5º clockwise or 5º
anti-clockwise to correct this.

1

Remove the two retaining screws under
decorative cover and then pull bottom of 
decorative cover while lifting. 

Pull bottom of internal grille while lifting. 

2

6

7

Replace decorative cover by hooking onto the
top of grille on the main body then push bottom
of cover home. Align screw holes with metal
retaining bracket and gently tighten retaining
screws at bottom of cover, ensuring no wires are
trapped.

Replace internal grille by hooking the top of
grille onto main body then push bottom of grille
home. 

Reviews: