BIRO EMG-32 Operating Manual And Parts List Download Page 18 | Manualshive

Page: 18 / 40

background image

16

#53953, MIXER DRIVE SHAFT SEAL REPLACEMENT

l. Clean the inside of the groove of the mixer drive shaft seal and mating contact surface of the tub wall

thoroughly with scotch-bright or a roughing pad.
2. Dispense a small amount of #454 Loctite adhesive to both these areas - assure even coverage.
3. Wipe away excess adhesive.

4. Slide the “Pressing Rings” #ST90 and #ST91 over the ends of the mixer drive shaft.
5. Apply “even” pressure to the Rings by installing the paddles and Bearing End Assemblies.

6. Wait 20 minutes Cure-Time.

7. Remove the “Pressing Rings.” The seals will be firmly attached to the tub wall.

NOTE: Part Number for 454 Loctite is #53953A-1

«
...
16
17
18
19
20
...
»

Summary of Contents for EMG-32









































Reviews:

No comments

Related manuals for EMG-32

Brand: Proctor-Silex Pages: 4

POLY-PTX 802 HT

Brand: eisenblatter Pages: 20

Brand: Cuisinart Pages: 20

Brand: Northern Industrial Pages: 12

Brand: Graphite Pages: 100

TGM 40230 Handy

Brand: EWM Pages: 23

Brand: CPS Pages: 19

Brand: Yamato Pages: 13

Brand: Kobalt Pages: 36

Brand: Alpha tools Pages: 60

Coffee Bar DGB-300 Series

Brand: Cuisinart Pages: 15

Brand: ARO Pages: 11

Brand: Chicago Pneumatic Pages: 2

Brand: Parkside Pages: 108

Brand: Parkside Pages: 142

Brand: SUHNER Pages: 36

Brand: BUTCHER BOY Pages: 11

Brand: BUTCHER BOY Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands