background image

i

Safety Precautions

The following are general safety precautions that are not necessarily related to 

any specific part or procedure, and do not necessarily appear elsewhere in this 

publication. These precautions must be thoroughly understood and apply to all 

phases of operation and maintenance.

WARNING

Keep Away From Live Circuits

Operating Personnel must at all times observe general safety precautions. Do 

not replace components or make adjustments to the inside of the test 

equipment with the high voltage supply turned on. To avoid casualties, always 

remove power.

WARNING

Shock Hazard

Do not attempt to remove the RF transmission line while RF power is present.

WARNING

Do Not Service Or Adjust Alone

Under no circumstances should any person reach into an enclosure for the 

purpose of service or adjustment of equipment except in the presence of 

someone who is capable of rendering aid.

WARNING

Safety Earth Ground

An uninterruptible earth safety ground must be supplied from the main 

power source to test instruments. Grounding one conductor of a two 

conductor power cable is not sufficient protection. Serious injury or death can 

occur if this grounding is not properly supplied.

WARNING

Resuscitation

Personnel working with or near high voltages should be familiar with modern 

methods of resuscitation.

WARNING

Remove Power

Observe general safety precautions. Do not open the instrument with the 

power applied.

Summary of Contents for 4043E




























Reviews: