Biotek Biolux HOS Series Owner'S Manual Download Page 5

Introduction

         

            

These safety precautions and warnings are provided at YOUR benefit to your health and home, 

for the safe and proper use of this unit and can prevent danger, bodily harm and/or possible damage 

due to misuse. 

Please make sure you are familiar with all the safety precautions and warnings associated with 

this unit. 

Biolux is not responsible for any damage or injury caused by not adhering to these precautions and

warnings.

When moving the unit, please be sure not to drag by the power cord as this could cause electric shock.

Do not place ANY objects on top of this unit regardless of how small.

Do not pull the power cord. Never touch power cord or power outlet with wet hands.

Do not use power surge protectors with this unit. Use unit with its own dedicated power source.

Do not forcibly bend, squeeze, damage or crush the power cord under heavy objects.

Do not use the unit in a dusty place. This may cause the unit to malfunction.

Do not spray water on the main unit. Do not clean with a damp cloth or any chemicals, which may leak into 

the unit.

Do not place this unit on an uneven surface. Do not drop or use excessive force on this unit.

Place this product near a sink and always allow water to drain into the sink and drain.

Please be sure to keep the power cord dust free.

In case water leaks out of the unit (other than hoses) or unit is standing in a puddle of water, shut off the 

water supply, unplug the power cord and refer servicing to qualified service personnel.

In the event that water gets into power supply, unplug the power cord and completely dry power outlet.

In case of strange noises, burning odor or smoke, unplug the power cord immediately and refer

servicing to qualified service personnel.

Replace pre-filter at least every 12 month or follow the recommendation from manufacturer in order to 

optimize the purification performance of this unit even if the replacement indicator light isn’t turned on.

Do not poke or scratch the touch pad or LCD display with sharp objects.

Keep original packaging for storage or unit transportation.

If the power cord develops a break or short, stop using the unit and call customer service to have it replaced.

Do not reconnect or splice a defective power cord as it could result in electric shock or become a fire hazard.

8. 

9. 

10. 

11. 

12. 

13. 

14. 

15. 

16. 

17. 

18. 

19. 

20. 

21. 

22. 

23. 

24. 

25. 

4

Summary of Contents for Biolux HOS Series


































Reviews: