Biostar M6VLA Page 72 User Manual Download

Page: 72 / 76

Chapter

Trouble

Shooting

4-6

PROBLEM

Screen is blank.

PROBABLE CAUSE

DIAGNOSIS

SOLUTION

No power to monitor.

Check the power
connectors to monitor and
to system. Make sure
monitor is connected to
display card, change I/O
address on network card if
applicable

Monitor not connected to
computer.

See

instructions

above.

Network card I/O address
conflict.

See

instructions

above.

PROBLEM

PROBABLE CAUSE

DIAGNOSIS

SOLUTION

Memory problem, display
card jumpers not set
correctly.

Reboot

computer.

Reinstall memory, make
sure that all memory
modules are installed in
correct sockets. Check
jumper and switch
settings on display card.
See display card section
for information on
settings.

Computer virus.

Use anti-virus programs
(mcAfee, E-Prot, etc) to
detect and clean viruses.

Summary of Contents for M6VLA













































































Search results

Summary of Contents for M6VLA

Reviews:

Related manuals for M6VLA

Brands by name

Popular brands

Biostar M6VLA, User Manual

Search results

Summary of Contents for M6VLA

Reviews:

Related manuals for M6VLA

Brands by name

Popular brands