Biostar M6VLA Page 50 User Manual Download

Page: 50 / 76

Chapter 2

BIOS Setup

2-20

Onboard FDD Controller

Select Enabled if your system has a floppy disk controller (FDD) installed on the
system board and you wish to use it. If install and FDD or the system has no
floppy drive, select Disabled in this field.

The Choices: Enabled

(default), Disabled.

Onboard Serial Port 1

Select an address and corresponding interrupt for the first and second serial ports.

The Choices: Auto

(default), 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4,

2E8/IRQ3, Disabled

Onboard IR Port

Select IR Address.

The Choices:

Auto, 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4,

2E8/IRQ3,

Disabled

(default).

UART 2 Mode

This item allows you to determine which Infrared (IR) function onboard I/O chip.

The Choices: HPSIR

(default), ASKIR.

IR Function Duplex

This item allows you to decide to active IR transmission delay.

The Choices: Half

(default), Full.

Tx, Rx inverting enable

This item allows you to determine the active of Rx,Tx.

The Choices: No/Yes

(default), No/No, Yes/No, Yes/Yes.

Onboard Parallel Port

This item allows you to determine access onboard parallel controller with which
I/O Address.

The Choices: 378/IRQ7

(default), 278/IRQ5, Disabled, 3BC/IRQ7.

Summary of Contents for M6VLA













































































Search results

Summary of Contents for M6VLA

Reviews:

Related manuals for M6VLA

Brands by name

Popular brands

Biostar M6VLA, User Manual

Search results

Summary of Contents for M6VLA

Reviews:

Related manuals for M6VLA

Brands by name

Popular brands