background image

BIH11-AHB User’s Manual

 

Chapter 1: Introduction | 3

 

 

 

Chapter 1: Introduction

 

1

1 Before You Start

 

Thank you for choosing our product. Before you start installing the motherboard, please make

 

sure you follow the instructions below:

 

 

Prepare a dry and stable working environment with sufficient lighting.

 

 

Always disconnect the computer from power outlet before operation.

 

 

Before you take the motherboard out from anti-static bag, ground yourself properly 
by touching any safely grounded appliance, or use grounded wrist strap to remove the 
static charge.

 

 

Avoid touching the components on motherboard or the rear side of the board unless

 

necessary. Hold the board on the edge, do not try to bend or flex the board.

 

 

Do not leave any unfastened small parts inside the case after installation. Loose parts

 

will cause short circuits which may damage the equipment.

 

 

Keep the computer from dangerous area, such as heat source, humid air and water.

 

 

The operating temperatures of the computer should be 0 to 45 degrees Celsius.

 

 

To avoid injury, be careful of:

 

Sharp pins on headers and connectors

 

Rough edges and sharp corners on the chassis 
Damage to wires that could cause a short circuit

 

 

 

 

» 

The package contents may be different due to the sales region or models in which it was sold. For 

more information about the standard package in your region, please contact your dealer or sales

 

representative.

 

Note

 

Summary of Contents for BIH11-AHB



















Reviews: