background image

PROGRAMMING YOUR ECO-OXIDIZER

PROGRAMMING YOUR ECO-OXIDIZER

The only setting on the Eco-Oxidizer that ever needs 
to be changed is the Oxidizing Output level. This is a 
setting  of  how  much  oxidizing  power  is  applied 
across the two electrodes.

To change the output setting :

!

  Press the 

button repeatedly until 

Oxidizing Power

 

the desired setting is shown with the LEDs.

!

  After 3 seconds, the Eco-Oxidizer will beep, save 

the new setting, and return to normal operation.

Suggested  output settings :

Off .......Oxidizing Output is switched off and will not 

operate.

1 to 3....Ignore  these  settings  unless  the  pump  is 

running for 16+ hours / day on a small pool.

4 ..........Suitable for up to 50,000 L (13,000 Gallons) 

Pool Size

5 ..........Suitable  for  50,000L  to  75,000L  (13,000  to 

20,000 Gallons) Pool Size

Max .....Suitable for 75,000L to 100,000L (20,000 to 

26,000 Gallons) Pool Size

For pools larger than 100,000L (26,000 Gallons), set 
the output to Max, but use two Oxidizing Pods.

For pools larger than 250,000L (66,000 Gallons), use 
two Eco-Oxidizers, each with two Oxidizing Pods.

Notes regarding output settings:

!

  The  pool  sizes  listed  are  an  approximate  guide 

only, and can vary with factors such as :

!

  Pool  loading:  The  number  of  bathers  in  the 

pool  compared  to  pool  size.  For  example,  a 
35,000L (10,000 Gallon) plunge pool with 10 
bathers  has  a  much  higher  load  than  a 
100,000L ( 26,000 Gallon) pool with 1 bather. 

!

  Water  temperature:  A  heated  pool  would 

require a higher setting than a pool with colder 
water.

!

  Location: A pool in a cooler climate area will 

require a lower output setting than a pool in a 
tropical  climate.  High  rainfall  would  also 
require a higher output setting.

How to find the optimum setting for your pool:

When  the  Eco-Oxidizer  is  first  installed,  select  the 
setting  as  per  the  information  in  the  “Suggested 
output settings” section.

Visually check your pool daily. If the water becomes 
dull or cloudy instead of crystal clear, increase the 
setting by one level. Recheck a day or two later.

When a pool is over-oxidized the main visual effect is 
the presence of too many tiny bubbles in the water, 
which can look like cloudiness. If your pool has this 
effect, reduce the setting by one level. Recheck a day 
or two later.

INSTRUCTION BOOK

10

Summary of Contents for Eco - Oxidizer

















Reviews: