P L E A S E R E A D A N D S AV E T H E S E
I M P O RTA N T S A F E T Y I N S T R U C T I O N S
F E AT U R E S - O P E R AT I O N S
Converting to a Table Fan
An additional short pole (Q) is supplied which allows the
fan to be converted into a table fan (see Figure 2). To
change to this short pole, remove the fan head assembly
from its position on top of the inner pole extension (N)
and unscrew the T-shaped locking lever (U) at the base.
Remove the outer pole (P), replace with the short pole
(Q) and reassemble as detailed above.
OPERATING INSTRUCTIONS
1. Set fan base on a dry, level surface.
2. Plug cord into any standard 120 volt AC outlet.
Please make sure the Speed Control Knob is in the
OFF (O) position. Speed Control Knob is located on
the Fan Motor Housing.
3. The SPEED is adjusted by turning the Speed Control
Knob to the desired setting, O-3-2-1.
4. The OSCILLATION control knob is located on the top
of the Fan Motor Housing. To start Oscillation, push
Control knob down. To stop Oscillation, pull Speed
Control Knob up.
ADJUSTMENT INSTRUCTIONS
Tilt-Adjustment
Follow these instructions to tilt the Fan Head for upward
angle air movement.
1. To change the tilting angle of the fan head, simply
loosen the tilt-adjustment knob (K).
2. Move the fan head to the desired angle and firmly
tighten the tilt-adjustment knob to lock into place.
Height Adjustment
Follow these instructions to adjust the height of the fan.
1. Turn the pole locking knob (O) counter-clockwise to
loosen the pole.
2. Adjust the pole to the desired height and firmly
tighten the locking knob in a clockwise direction.
CLEANING/MAINTENANCE INSTRUCTIONS
Follow these instructions to correctly and safely care for
your fan. Please remember:
REPLACEABLE FUSE
If your (5 Amp, 125 Volt) replaceable fuse blows, please
order a new fuse at 1-800-253-2764. Follow the below
instructions to replace the fuse on the plug.
User Servicing Instructions
1. Unplug your fan. Grasp plug and remove from the
receptacle or other outlet device. Do not unplug by
pulling on cord.
2. Open fuse cover, located on the top of the plug, by
using your thumb or a flathead screwdriver to slide
the cover down towards the prongs.
Note:
Ensure that fuse cover is completely open
before attempting to remove fuse.
3. Remove fuse carefully by using a small screwdriver
to pry the fuse out of the
compartment by the metal
ends of the fuse (see Fig. 3).
4. Place plug on a solid, flat
surface. Insert new 5 Amp,
125 Volt fuse into fuse
compartment and use a
small screwdriver to secure
the metal ends of the fuse
into the compartment.
Caution:
Risk of fire. Replace fuse only with 5 Amp,
125 Volt fuse.
5. Slide fuse cover closed completely. If fuse cover is
difficult to close, make sure fuse is secured in place
completely by pressing down on metal ends of the
fuse.
6. Risk of fire. Do not replace attachment plug. Contains
a safety device (fuse) that should not be removed.
Discard product if the attachment plug is damaged.
ASSEMBLY INSTRUCTIONS
Assembly Time: 10-15 minutes.
Tools Required: Phillips head screw driver.
NOTE:
Make sure you remove all contents from the
package. Please check packaging materials for parts that
could be required to operate your fan.
Base/Pole Assembly
You will need the base cover (R), weight (S), outer pole
(P), washer (T) and T-shaped locking lever (U).
1. Turn the base cover upside down and place the
weight into the base cover.
2. Insert the threaded end of the T-shaped locking lever
into the hole of the washer, weight and through the
base cover.
3. While holding the base cover and weight with one
hand vertically, connect the outer pole to the base,
sliding the T-shaped locking lever into the bottom of
the outer pole with your other hand.
4. Turn the T-shaped locking lever clockwise to securely
attach the pole to the base.
5. Set the base on the floor, weight side down.
Fan Head Assembly
You are now ready to assemble the fan head.
1. Remove the protective sleeve (G) and unscrew grill
mounting nut (D) by turning counter-clockwise from
the motor shaft (F). Position the rear grill (E) over
the motor shaft (F), making certain that the vertical
slots at the top and bottom of the rear grill fit over
the prongs on the motor housing (H). Make sure that
the carry handle is topmost on the motor assembly.
2. Secure the rear grill (E) in its place using the rear
grill mounting nut (D). Turn this nut clockwise and
tighten firmly.
3. Loosen the securing screw (C) on side of the fan
blade (B) to slide the fan blade onto the motor shaft
(F) through the rear protrusion. Make sure the
securing screw (C) rest on the notch (flat side) of
motor shaft and tighten the screw (C).
CAUTION:
Avoid contact with sharp end of blades.
4. Centre the front grill (A) by aligning the Bionaire
®
logo on the logo plate so that it is horizontal and
parallel with the floor. Then place the bracket at the
top over the front and rear grills with the hole on the
bracket going through the center vertical bar. Fasten
the other clips, making sure they go over both the
front and rear grills.
5. Replace grill screw and nut (V) and tighten with screw
driver.
Final Assembly
NOTE:
The fan head locking knob (L) is attached with
the additional short pole (Q) when shipped.
1. Slide the inner pole extension (N) up from the outer
pole (P), first loosening the pole locking knob (O), to
securely hold this position. Tighten the pole locking
knob (O).
2. Place the fan head assembly into this extension pole,
inserting the fan’s head neck (M) into the pole
opening.
3. Add the fan head locking knob (L) to the hole in the
fan head's neck (M), making sure holes are aligned,
and tighten.
When using electrical appliances, basic safety precautions
should always be taken including the following:
1. Read all instructions before using this appliance.
2. Use fan only for purposes described in the instruction
manual.
3. To protect against electrical shock do not immerse
unit, plug or cord in water or spray with liquids and
plug the appliance directly into a 120V AC electrical
outlet.
4. Close supervision is necessary when any appliance is
used by or near children.
5. Unplug from outlet when not in use, when moving
fan from one location to another, before putting on
or taking off parts and before cleaning.
6. Avoid contact with moving parts.
7. Do not operate in the presence of explosive and/or
flammable fumes.
8. To avoid fire hazard, NEVER place the cord under
rugs or any parts near an open flame, cooking or
other heating appliance.
9. Do not operate any appliance with a damaged cord
or plug after the appliance malfunctions, or has been
dropped/damaged in any manner. Discard fan or
return to an authorized service facility for
examination and/or repair.
10. Do not run cord under carpeting. Do not cover cord
with throw rugs, runner, or similar coverings. Do not
route cord under furniture or appliances. Arrange
cord away from traffic area and where it will not be
tripped over.
11. The use of attachments not recommended or sold by
the appliance manufacturer may cause hazards.
12. Do not let the cord hang over the edge of a table,
counter or come in contact with hot surfaces or leave
exposed to high traffic areas.
13. Do not use outdoors.
14. To disconnect, grip plug and pull from wall outlet.
Never yank on cord.
15. Always use on a dry, level surface.
16. Do not operate fan until fully assembled with all
parts properly in place.
17. This product is intended for household use ONLY and
not for commercial or industrial applications.
18.
WARNING:
To reduce the risk of electrical shock
and injury to persons, do not use in window.
19.
WARNING:
To reduce the risk of fire or electric
shock, do not use this fan with any solid-state speed
control device.
20. This product employs overload protection (fuse). A
blown fuse indicates an overload or short-circuit
situation. If the fuse blows, unplug the product from
the outlet. Replace the fuse as per the user servicing
instructions (follow product marking for proper fuse
rating) and check the product. If the replacement
fuse blows, a short circuit may be present and the
product should be discarded or returned to an
authorized service facility for examination and/or
repair.
PLEASE READ AND SAVE
THESE IMPORTANT SAFETY
INSTRUCTIONS
F E AT U R E S - O P E R AT I O N S
C L E A N I N G / M A I N T E N A N C E
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit in
a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
Fuse cover
Fig. 3
Metal ends
Fuse
A
Fig. 1
B
C D
E
F
V
G H
I
M
O
P
Q
R
S
T
U
J
K
N
L
A Front Grill
B. Fan Blade
C. Securing Screw
D. Grill Mounting Nut
E. Rear Grill
F. Motor Shaft
G. Plastic Sleeve
H. Motor Housing
I. Speed Control Knob
J. Oscillation Control Knob
K. Tilt Adjustment Knob
L. Fan Head Locking Knob
M. Fan Head's Neck
N. Inner Pole Extension
O. Pole Locking Knob
P. Outer Pole
Q. Additional Short Pole
R. Base Cover
S. Weight
T. Washer
U. T-Shaped Locking
Lever
V. Grill Screw and Nut
Base Cover
Additional Short Pole
Fig. 2
BSF1211C-MU_12EM1.indd 2
10/12/12 11:13 AM
