background image

Wireless Series

Warranty does not cover the batteries, damages due to misuse,abuse  or accidents,

cracked or broken cases, negligence of precautions, improper maintenance or 

LIMITED WARRANTY

 Wireless Series computer

Unscrew the back cover. The (+) side should be facing up.

Gently remove the battery and replace it with a new battery model CR2032.

Under the SCAN MODE, the display will automatically show all modes in 

circulating loop every 4 seconds. Once the speed has been detected. Press any key

to stop SCAN faeture.

.

Receiver

Operating Temperature
Storage Temperature
Battery
Weight

17.7 grams

0 ~ 40

-10 ~ 50

3 volt lithium 2032 cell

Timer Range : 29 (hour) : 59 (minute) : 59 (Second)

Current Speed Range : 0~99.9 KM / 0~62.4 Mile

Average Speed Range : 0~99.9 KM / 0~62.4 Mile

MAX Speed Range : 0~99.9 KM / 0~62.4 Mile

(Trip) Distance Range : 0~999.99 KM / 0~624.99 Mile

Odometer Range : 0~99999 KM / 0~62499 Mile

KCAL:0~99999 kcal

Wheel Circumference

To get the accurate result, the wheel size should be correct Mark the symbol on the 

tire and ride one circle. Then measure the length between two points to get the 

circumference. Or the user can also get wheel circumference by the following 

equation:

Circumference(mm) = 2 x 3.14 x R(inch) x 

2.54(1 inch=2.54 cm)

R=Radius in centimeter

Press Mode key shortly to change mode.

CLK MODE (Clock Mode)
TM MODE (Trip Time Mode) 
AVS MODE (Average Speed Mode) 

MXS MODE (Max Speed Mode)

DST MODE (Distance Mode)

AVS MODE (Average Speed Mode)

The average speed

from the beginning 

onwards.

MXS MODE (Maximum Speed Mode)

DST MODE (Distance Mode)

The user can refer the 

"wheel size chart"

for the

wheel size.

The maximum speed from

the beginning onwards.

Note:

If the time or distance is over the max value ( 29 hr: 59 min: 59 sec

or Distance: 999.99km), It will not be able to measure correct average

 

speed by showing "Err" on the display. Once the time & distance value

 

has been reset, the average speed will show normally.

KCAL MODE (Calorie Mode)

SCAN MODE

It displays the accumulated calories consumed from the beginning of the trip

onwards.

Note: This accumulated calories display will return to 0 once it has been 

clear under the TM MODE.

How to input weight, weight scale and gender

Press  key for 3 seconds to setting mode.

Press  key to select MALE or FEMALE, and wait 3 seconds to weight unit mode

Press  key to select preferable KG or LB, and wait 3 seconds to weight mode

Press  key to input the weight in numbers.

  Wait for 5 seconds to exit.

This product is for one year limited warranty commencing on the date of purchase.

The product will be free from defects in material and workmanship for one year

from the date of purchase.

Battery Replacement

Q1. Display is black or very light:

The battery power may be low. Try a new battery to make sure the battery is installed correctly

Q2. Display becomes dark or black:

The unit is too hot. Place the unit in a shaded area, and it will return to normal

Q3. The unit operates slowly or struggled:

The unit is too cold. Warm the unit, and it will return to normal.

Q4. Data in display varies enormously:

Check the surroundings for electro magnetic or high energy interference and move 
away from the source of interference.

Q5. Data in display shows slowly:

The unit may be affected by low temperature factor but it didn't influence the function  
reading. When the temperature rises, the data reading/ witch will back to the normal.

Q6. Current speed does not appear

It may be caused by the following situation: the distance & position between 
magnet and sensor to adjust.

TROUBLESHOOTING

ODO  MODE 
KCAL  MODE (Calories Mode) 
SCAN  MODE 

  

 

Trip Timer would operate automatically when the bike is in motion. 

Press and hold key for 3 seconds,all exercises results in displayer will

 

return to zero, except odometer.

TM MODE (Trip Time Mode)

3sec

3S

3S

3S

3S

3S..

3S..

M

M

M

M>3S

M

W.s.100~2999

Under ODO Mode, press key for 3 seconds to go to setting.

Press key to select Km/H or Mile/H, then wait 3 seconds to go to wheel setting

In Wheel Settings. Input the correct wheel size by pressing key. 

Range of wheel size from 100mm to 2,999mm, wait 3 seconds to go to ODO setting

For users to input previous accumulated ODO after new battery 

Go to ODO Setting. Input the previous ODO  by pressing key, the range 

KM:0~99999, ML:0~62455

kg:20~150

Lb:44~300

Sensor

Unscrew the back cover. The (+) side should be facing up.

Gently remove the battery and replace it with a new battery model CR2032.

TM

TM

TM

In Clock Mode, hold key for 3 seconds to set clock. Press Key to adjust time 

(hour,minute,second) Every 3 seconds the display will show the next setting.

M>3s

Please read over the following information before using the Cycle computer.

Warranty is void if the repairs are done by non authorized service technician.

The warranties contained herein are expressly in lieu of any other warranties including

implied warranty of merchantability and/ or fitness for purpose. In no event shall

manufacturer be liable for any damages, direct or incidental, consequential or special,

arising out of or related to the use of this manual or the products described herein. 

During this warranty period (one year) the product will either be repaired or 

replaced without charge.

commercial use.

M>3s

3s

3s

3s

3s

of ODO is from 1 to 99999.

Wait for 3 seconds to go back to ODO Mode.

24H/12H

0~23

12~11,12~11PM

0~59

0~59

 Wireless Series computer

 Wireless Series computer

Bracket

Nylon Ties

(2)

(1)

Rubber

Bracket

Cycle Computer

Rubber

Bracket

Cycle Computer

Use the rubber to tighten the bracket to the handlebar or stem with the nylon ties.

Place the cycle computer on the bracket and secure it in clockwise.

Check the position of the front fork to find the suitable point to attach the speed sensor.  

The distance between cycle computer & the speed sensor would be with 60 cm. 

Mount the sensor with nylon ties on the chosen front fork. 

How to mount the Magnet

Note:

Please make sure everything has been setup correctly before riding the bicycle.

Secure the Speed Magnet on the spoke of the front wheel with screw.

Make sure the magnet side faces the speed sensor zone.

The maximum distance between the speed sensor and the magnet on the spoke is 5 mm. 

Once above items in the right position, the user may go for a ride.

(3)

(5)

Magnet

Screw

(6)

cycle computer 

Battery cover

x4 Pcs

Speed

Magnet

Rubber

Bracket

Mode Key

Set Key

Current Speed

PM indicator

Speed unit 

Mode Indicator

Speed arrow 

Comparison

Reviews: