manualshive.com logo in svg

BIO RAD PowerPac Universal Power Supply, Instruction Manual

Share
Download
BIO RAD PowerPac Universal Power Supply Instruction Manual Download Page 11

 

PowerPac Universal Power Supply Instruction Manual 

Page | 3 

1.2   Unpacking 

When you receive your power supply, carefully inspect the container for any damage 

which might have occurred in shipping. Severe damage to the container might indicate 

damage to the power supply itself. If you suspect damage to the unit, immediately file a 

claim with the carrier in accordance with their instructions before contacting Bio-Rad 

Laboratories. 

After unpacking the PowerPac Universal, remove the plastic film from the translucent 

green top case. The plastic film might leave a residue. If so, clean with a soft, damp 

cloth. Also remove the die-cut plastic film covering the display window. 

Contents include: 

•

  PowerPac Universal power supply 

•

  Power cord 

•

  Instruction manual 

•

  Warranty card 

•

  Declaration of conformity 

NOTE:

 If any part is missing, contact Bio-Rad Laboratories immediately. 

 

 

Summary of Contents for PowerPac Universal Power Supply











































Reviews:

No comments

Brands by name

Popular brands

Load more brands