manualshive.com logo in svg

bintec elmeg H2 Auto Compact Series, Installation Manual, Page: 34 / 40

Share
Download
bintec elmeg H2 Auto Compact Series Installation Manual Download Page 34

A.4.2 LAN interface

PROTOCOLS

Ethernet (802.3).

PORTS

2-port switch managed through MDI/MDX self-detection.

SPEED

10/100/1000 Mbps (BaseT).

CONNECTOR

RJ45 Female.

A.4.3 Wireless WAN interface

WWAN Standard/Bands

EC25-E:

• LTE:

• FDD. B1, B3, B5, B7, B8, B20

• TDD: B38, B40, B41

• WCDMA: B1, B5, B8

• GSM/GPRS/EDGE: 900/1800 MHz

Speed (DL/UL)

EC25-E:

• LTE Cat 4.

• FDD. 150Mbps/50Mbps

• TDD: 130Mbps/35Mbps

• HSPA+ Cat 24/6: 42Mbps/5.76Mbps

• EDGE: 236Kbps

CONNECTOR

Up to two SMA female connectors.

SIM Slots

2 Mini-SIM (2FF) ISO/IEC 7810:2003, ID-000 (1.8V / 3V)

General

VSWR: # 2

Efficiency: > 30%

Max input power: 50W

Input impedance: 50#

Antenna Requirements

Cable insertion loss: < 1dB

(EGSM900, WCDMA B5/B8, LTE-FDD B5/B8/B20)

Cable insertion loss: < 1.5dB

(GSM1800, WCDMA B1, LTE-FDD B1/B3)

Cable insertion loss: < 2dB

(LTE-FDD B7, LTE-TDD B38/B40/B41)

Technical information

bintec elmeg GmbH

28

bintec H2 Auto Compact

Summary of Contents for H2 Auto Compact Series









































Reviews:

No comments