Billy Goat TERMITE KD510SP, Operator Owner'S Manual

Page: 12 / 12

Part No. 890424 Form No. F011398A Page 12 of 12
Engine Service and Warranty
Contact your nearest engine manufacturer's autho-
rized servicing dealer.
22.1 22.1 22.1 22.1 22.1
22 22
22 22 22
BILLY GOAT INDUSTRIES INC.
P.O. BOX 308 (1803 S JEFFERSON) LEE'S SUMMIT, MO 64063 / USA
PHONE: 816-524-9666 FAX: 816-524-6983
R
WARRANTY PROCEDURE
Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
The WARRANTY terms are stated on the lower part which remains with the
user. Whenever a Billy Goat Machine is faulty due to a defect in material
and / or workmanship, the owner should make a warranty claim as follows:
The Machine should be taken to the dealer from whom it was
purchased or to an authorized Billy Goat dealer.
The owner should present the remaining half of the Warranty
Registration Card, or, if this is not available, the invoice or receipt.
The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
who will send it with the faulty part to Billy Goat headquarters.
The Quality / Service department at Billy Goat headquarters will study
the claim and parts and will notify their conclusions.
The decision by the Quality / Service department at Billy Goat
headquarters to approve or reject a Warranty claim is final and
binding.
Note: To process a Warranty Claim, it is necessary to quote the Model
& Serial number who are printed on the Billy Goat Serial Plate.
Purchased
from Purchase
Date
21 21 21 21 21
Serial Plate
R
ecord your machine model, serial number
and date-of-purchase and where purchased
R
min
-1
Operator
1803 S. Jefferson
P.O. Box 308
Lee's Summit,
MO 64063 / USA
Tel (816) 524-9666
Fax (816) 524-6983
Model Serial No.
Unit(Weight) Engine Power
lbs. kg kW rpm
L
A
p
109
97
L
A
Engine stalls or labors when
chipping.
Feeding branches into chipper too rapidly. Engine service may be
required.
Feed branches at a slower rate. Service engine.
Poor chipping performance.
Extremely hard wood. Dull or damaged chipper blade.
Avoid extremely hard wood. Sharpen or replace chipper blade (see
page 8).
Will not vacuum or has poor
vacuum performance. Clean debris bag. Shake bag clean or wash. Adjust nozzle height.
Check for hose kit cap. Unclog nozzle or exhaust (see page 5).
Allow air to feed with debris.
Solution Problem Possible Cause
TROUBLESHOOTING
Before Requesting Service Review These Suggestions
Engine will not start. Check stop switches, throttle, and gasoline. Connect spark plug wire.
Clean or replace air cleaner. Or contact a qualified service person.
Self propelled drive will not
release. Clutch cable out of adjustment. Clutch not lubricated and is locked-
up. Adjust clutch cable. See page 9 Clutch Adjustment. Oil clutch.
No self propelling. Operator's bail not releasing clutch. Broken or out of adjustment
clutch cable. Worn or broken clutch assembly. Bracket control
assembly (item 112) out of adjustment. Adjust clutch cable. Adjust bracket control assembly. Replace any
worn or damaged or malfunctioning parts.
Throttle in off position. Out of gasoline. Bad or old gasoline.
Spark Plug wire disconnected. Dirty air cleaner.
Abnormal vibration.
Loose or out of balance impeller or loose engine.
Check impeller and replace if required. Check Engine.
Engine is locked, will not
pull over. Debris locked in chipper blade, hopper or inside impeller. Engine
problem. See page 5, Clearing a clogged chipper hopper. Contact an engine
servicing dealer for engine problems.
Dirty debris bag. Nozzle height set too high or too low. Hose kit cap
missing. Clogged nozzle or exhaust. Excessive quantity of debris.
20
19
( Continued from
page 11 )
PARTS LIST
Item
No. Description
KD510SP Part
No. Qty.
TKD510SP Part
No. Qty.
86 Wheel With Sprocket Ass'y Cast ( 21, 94, 95, 96) 890242 2 890242 2
87 Chain 52 Pitch 890239 2 890239 2
88 Chain 40 Pitch 900323 1 900323 1
89 Washer Flat 5/16 (3/8 ID x 7/8 x 1 1/6) *8171003 4 *8171003 4
90 Bolt Carriage 5/16 - 18 x 3/4 *8024039 4 *8024039 4
91 Washer Spring Lock 5/16 *8177011 4 *8177011 4
92 Nut Regular 5/16 - 18 *8142002 4 *8142002 4
93 Jackshaft 900320 1 900320 1
94 Sprocket (per Assemby) (size # 65A26) 26 Teeth 890238 1 890238 1
95 Screw Self Tap 1/4-14 x 3/4 (Per Assembly) 800505 5 800505 5
96 Washer Lock External Tooth (Per Assembly) *8181007 5 *8181007 5
97 Jackshaft Ass'y (incl. 93, 101, 102, 107, 108, 109) 890197 1 890197 1
98 Shield Muffler TKDSP 890190 1 890190 1
99 Label Clutch 830503 1 830503 1
100 Label - Warning Guards 900327 1 900327 1
101 Bearing Plate 900317 2 900317 2
102 Bearing Ball (with Snap Ring) 900321 2 900321 2
103
104 Rod Bail Clutch
900970 1 900970 1
105
106
107 Sprocket - 17 Tooth
900303 1 900303 1
108 Sprocket - 8 Tooth 900302 2 900302 2
109 Roll Pin 3/16 Dia. x 1 1/4 Lg. *8195166 4 *8195166 4
110 Locknut 5/16 - 18 Flange 850164 5 850164 5
111
112 Bracket Control Ass'y (incl. 113, 114, 115)
900221 1 900221 1
113 Spring 900136 1 900136 1
114 Roll Pin 1/8" Dia. x 1 1/4 Lg. *9195106 1 *9195106 1
115 Rod Clutch 900208 1 900208 1
116 Screw Cap 1/4-20 x 1" Lg. *8041006 2 *8041006 2
117 Washer 1/4" Flat (5/16 ID x 3/4 Od x 1/16) *8171002 4 *8171002 4
118 Guard Chain Ass'y TKDSP 890231 1 890195 1
119 Clip - Clutch Cable 900999 1 900999 1
120
121 Clutch Double Release
900307 1 900307 1
122
123 Label Read Owner's Manual 890301 1 890301 1