background image

POWER RAKE SEEDER BOX KIT-350395 AND 350397

 

 

Part No 350398 

                                - 1 -                                                          Form No F102207B 

 

 

 

 

 

 

 
 
 
 
 

 
 
 

 
 

 
 
 

 

 

 
 
 
 
                                                        

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

Seeder Box Installation: 
1. Disconnect spark plug wire. 
2. Support Power Rake on blocks to lift left front wheel off ground. 
3. Remove 4 screws from front of machine. 
4. Remove left front wheel. 
5. Install seeder box to front of machine with four 5/16” x 3/4 cap screws,
4 flat washers, and 4 lock washers. Do not tighten at this time (see figure 
1). 
 
Wheel:  
1. Slide the pulley on until it rests firmly against the hub. 
2. Tighten two setscrews. 
3. Be sure 3 washers  (item 31) are on the axle, slip the belt (item 24) in 
the groove on the pulley and slide wheel on the axle. 
4. Secure with lock nut (item 35). 

NOTE:

 Replace thick locknut with the thin nut provided in parts bag. 

New units are provided with thin nuts. 
 
Belt alignment: 
1. Attach the belt onto the seeder box pulley by turning the wheel and 
slowly feeding the belt onto the seeder box pulley. 
2. Rotate wheel to insure belt turns freely 
3. If the belt seems to be too tight, bump seeder box upward to loosen 
belt. 
4. Check the pulley alignment then tighten 4 capscrews inside seeder 
box. 
5.Repeat step 3 to 5 if necessary 
6. Remove blocks from under machine & push machine to test 
mechanism. 
 
Seeder meter control box installation: 
1. Attach the Seed drop control box (Item 2) to the upper handle with the 
hardware from the parts bag (Items 17, 28, 35, 36, 39, 40) using a 7/16” 
and a 9/16” wrench. Then attach the cable to the bail with hardware items 
42 and 43 using 5/16” and a 3/8” wrenches. Secure the cable with a ty- 
wrap (item 44) to the upper handle. 
2. Reconnect spark plug wire. 

PURPOSE: To overseed an existing lawn or start a new lawn. 
Tools Required: 3/16" allen wrench, 7/16”, 1/2", 5/8", 3/4", 9/16”, 5/16”, 3/8” wrench, Wood blocks or suitable support for 
machine. 

NOTE:

Older models with no holes will need additional tools:

3/8" drill bit and drill, center punch, two 1/2" wrenches.

INSTALLATION 

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Summary of Contents for 350395

Page 1: ...l and slowly feeding the belt onto the seeder box pulley 2 Rotate wheel to insure belt turns freely 3 If the belt seems to be too tight bump seeder box upward to loosen belt 4 Check the pulley alignment then tighten 4 capscrews inside seeder box 5 Repeat step 3 to 5 if necessary 6 Remove blocks from under machine push machine to test mechanism Seeder meter control box installation 1 Attach the See...

Page 2: ... 350271 PLATE DOOR DROP SEEDER 1 6 350272 PLATE DOOR DROP SEEDER END 1 7 350387 PLATE DOOR DROP SEEDER END ARM 1 9 350370 PULLEY 3V GROOVE 0 625 BORE 1 10 8172009 WASHER 10 3 8 SAE 1 11 900321 BEARING CLIP 1 375 OD 4 12 890108 KNOB WING 5 16 18 1 13 400217 SPRING TENSION 2 14 8024040 BOLT CARRIAGE 5 16 18 X 1 1 15 8024021 BOLT CARRIAGE 1 4 20 X 3 4 1 16 8123087 SCREW SELF TAP 10 24 X 3 8 HMS ZP 4 ...

Page 3: ...R PRIOR TO SEEDING POWER RAKE TO DETHATCH LAWN AND REMOVE THATCH FERTILIZE LAWN WITH BROADCAST SPREADER LAWN PREPARATION FOR BEST RESULTS OVERSEED IN TWO PASSES OF ONE HALF APPLICATION RATE EACH AT RIGHT ANGLES OR IN A CRISS CROSS PATTERN WATER HEAVILY IMMEDIATELY THEN LIGHTLY FOR 10 14 DAYS KEEPING SOIL MOIST AFTER GERMINATION WATER LESS OFTEN TO PROMOTE ROOT GROWTH ...

Page 4: ...an be reused if they are not damaged The lock washer twisted tooth p n 400502 57 screwcap reel pulley p n 8041050 71 and key 3 16 x 1 p n 9201078 42 must be replaced Note pulley key and spacer must be inserted only onto the side of the reel that will be driven by the engine The angled edge of the blades should be facing the direction in fig 1 to dig into the ground otherwise the machine will not p...

Reviews: