Big Joe PDSR 30 Installation, Operation, Maintenance & Repair Parts Download Page 34

Page: 34 / 172

4-16

BL-PDSR 30-0319 - 03-07-2019

248

S.P OUT OF RANGE

This alarm occurs for a fault on the

command potentiometer (CPOC2on

CNA#8). When a single command

pot is chosen, the alarm occurs if the

wiper (CPOC1) exits the range from

0.8 Vdc to 4.2 Vdc. When the twin

pot is chosen, the alarm occurs if the

sum of the two wiper voltages

(CPOC1 + CPOC2) exists the range

from

4.5 Vdc to 5.5 Vdc.

Check the connections of the potenti-

ometer. This alarm occurs when one

connection of the command potentiom-

eter is broken.

249

F.B OUT OF RANGE

This alarm occurs for a fault on the

feedback potentiometer (CPOT on

CNB#6). This alarm occurs in CPOT

exits the range from 0.3 Vdc to 4.7

Vdc.

Check the connections of the feedback

potentiomerter

This alarm occurs when

one connection of the feedback poten-

tiometer is broken.

250

MICRO SLAVE

It occurs when the information on

the status bus between the

main uC and the slave uC is frozen

to the OFF value (the slave uC does

not update the status bus configura-

tion).

It is necessary to replace the controller

251

KM OPEN

This alarm occurs if the slave uC

detects the safety contact, of the

main uC, o[pen when expected

being closed.

It is necessary to replace the controller

252

KS OPEN

This alarm occurs if the slave uC

detects the safety contact, of the

main uC, open when expected being

closed.

It is necessary to replace the controller

253

KM CLOSED

This alarm occurs at key-on if the

slave uC detects the safety contact,

of the main uC, closed prior to being

commanded.

This alarm occurs if the connection

CNA#5 (K1) is around a voltage of 12

Vdc when switching on the key

In fact,

when the safety contacts are open, K1

is expected to be plus battery voltage

(not 12 V). Search for a harness prob-

lem or replace the controller

254

KS CLOSED

This alarm occurs if the main uC

detects the safety contact, of the

slave uC, closed prior to being com-

manded.

This alarm occurs if the connection

CNA#4 (NK1) is around a voltage of 12

Vdc when switching on the key

In fact,

when the safety contacts are open,

NK1 is expected to be a minus battery

voltage (not 12 V). Search for a harness

problem or replace the controller

Error Message

Possible Cause

Fault Elimination

Code

Error Text

Summary of Contents for PDSR 30













































































































































































Search results

Summary of Contents for PDSR 30

Reviews:

Related manuals for PDSR 30

Brands by name

Popular brands

Big Joe PDSR 30, Installation, Operation, Maintenance & Repair Parts

Search results

Summary of Contents for PDSR 30

Reviews:

Related manuals for PDSR 30

Brands by name

Popular brands