Big Joe PDSR 30 Installation, Operation, Maintenance & Repair Parts Download Page 31

Page: 31 / 172

BL-PDSR 30-0319 - 03-07-2019

4-13

221

MICRO SLAVE #4

It occurs in one or the following con-

ditions:

(Open loop application only) If the

slave uC detects the stator voltage

phase rotates in the opposite direc-

tion respect to

the sign of the stepper motor speed.

(Closed loop application only) If the

slave uC detects the stator voltage

phase rotates in the opposite direc-

tion respect to the commanded posi-

tion.

It is necessary to replace the controller

222

FB POT LOCKED

In application with a feedback poten-

tiometer, this alarm occurs if the

feedback potentiometer (CPOT on

CNB#6) does not change (or

changes in the opposite direction) its

value even if commanded to

change.

In application with toggle switches

with ENCODER CONTROL to

off, this alarm occurs if the feedback

encoder counting does not change

its value even if commanded to

change.

In application with the feedback potenti-

ometer, verify potentiometer is not

mechanically loosened. Check there is

not a mechanical block of the steered

wheel. Be sure the wiper has not

reached its own electrical limit because

of too much angle of the steered wheel.

Besides, this alarm may occur at the

installation when the motor rotates in

the wrong direction turning away from

the desired direction.

223

JERKING FB POT

This alarm occurs if the feedback

potentiometer (CPOT on CNB#6)

changes with a jerk larger than 0.3V

in 16 msec. This alarm is used to

catch a discontinuity in the voltages

of the feedback potentiometer

Change the feedback potentiometer

225

CURRENT GAIN

This alarm occurs when the parame-

ter to compensate for the gain of the

current amplifiers (ADJUSTMENT

#03 and ADJUSTMENT #04) have

the default values.

It is necessary to send the controller to

Zapi to perform, the maximum current

regulation.

226

NO SYNC

Every 16msec, inside the code

cycle, the main uC rises and then

lowers an input for the slave uC

(SYNC). When the slave uC detects

no edge for more than 100 msec on

this input, this alarm occurs. This is

just a watch dog function:

when the main uC does not execute

the code cycle it does not update the

SYNC signal and the slave uC cuts

off the steer and traction.

It is necessary to replace the controller

Error Message

Possible Cause

Fault Elimination

Code

Error Text

Summary of Contents for PDSR 30













































































































































































Search results

Summary of Contents for PDSR 30

Reviews:

Related manuals for PDSR 30

Brands by name

Popular brands

Big Joe PDSR 30, Installation, Operation, Maintenance & Repair Parts

Search results

Summary of Contents for PDSR 30

Reviews:

Related manuals for PDSR 30

Brands by name

Popular brands