background image

© 2019 DELTA T LLC     ALL RIGHTS RESERVED.

7

MAINTENANCE

Electrical preventive maintenance 

Big Ass Fans suggests an electrical preventive maintenance program similar to 
that described in 

NFPA 70B: Recommended Practice For Electrical Equipment 

Maintenance

 by the National Fire Protection Association.

Cord safety 

If the external flexible cable or cord of this luminaire is damaged, it shall be 
exclusively replaced by Big Ass Fans or a Big Ass Fans service agent or a similar 
qualified person in order to avoid a hazard. For assistance, please contact 
Customer Service.

Emergency lighting testing

Test emergency lighting as described in 

NFPA 101: Life Safety Code. 

Keep written 

records of testing and make sure inspections are performed regularly. 

Monthly. 

Conduct a 30-second emergency lighting test. Press and hold the red, 

illuminated button on top of the fixture for 30 seconds. Make sure half of the LEDs 
operate at a dim level for the entire 30 seconds.

Annually. 

Conduct a 90-minute emergency lighting test. Switch off AC power at 

the circuit breaker to simulate a blackout. Make sure half of the LEDs operate at a 
dim level for 90 minutes.

Cleaning the lenses

Do not clean the fixture—especially the lenses—with scouring pads, alkaline 
cleaning substances, gasoline, thinner, benzene, heating oil, or polishing powder. 
Do not pressure wash or use a water hose to clean the fixture.
Clean the lenses periodically to ensure optimal performance. Remove lenses 
and wipe with a clean, damp cloth. Allow to dry thoroughly before replacing. If 
necessary, use a mild soap or a gentle liquid cleaner.

Summary of Contents for Delta T LLC dba













Reviews: