background image

 

Page 2 of 24                                                                                                                                                      M7159 iss 4.4 

 

 

 

Please take your time to read this Instructions book in order to understand the safe and 
correct use of your new Bibby Scientific product. 
 
It  is  recommended  the  Responsible  Body  for  use  of  this  equipment  reads  this 
Instruction book and ensures the user(s) are suitably trained in its operation. 

 

CONTENTS 

 

 

 

Section 1 

Introduction 

Page 3 

 

 

 

Section 2 

Symbols and using this Instruction book 

Page 4 

 

 

 

Section 3  

Safety Information. 

Page 5 

 

 

 

Section 4 

Unpacking and contents 

Page 7 

 

 

 

Section 5 

Installation 

Page 8 

 

 

 

Section 6 

Environmental Protection. 

Page 9 

 

 

 

Section 7 

Product Operation. 

Page 10 

 

 

 

Section 8 

Technical Specification. 

Page 12 

 

 

 

Section 9 

Maintenance 

Page 13 

 

 

 

Section 10 

Customer Support 

Page 18 

 

 

 

Section 11 

Spares and Accessories 

Page 20 

 

 

 

Section 12 

Notes 

Page 21 

 

 

 

Section 13  

EC declaration of Conformity 

Page 24 

 

 

 

Appendix A 

Decontamination Certificate. 

Page 19 

 

©

 The copyright of this instruction book is the property of Bibby Scientific Limited. This instruction book is supplied 

by  Bibby  Scientific  Limited  on  the  express  understanding  that  it  is  to  be  used  solely  for  the  purpose  for  which  it  is 
supplied.  It may not be copied, used or disclosed to others in whole or part for any purpose except as authorised in 
writing  by  Bibby  Scientific  Limited.  Bibby  Scientific  Limited  reserves  the  right  to  alter,  change  or  modify  this 
document without prior notification.  

 

In the interest of continued development 

Bibby Scientific Limited

 

reserve the right to alter or modify 

the design and /or assembly process of their products without prior notification. 

 

This product is manufactured in Great Britian by Electrothermal, part of the Bibby Scientific Group of 
companies.  

 

Bibby Scientific Limited.

 

Beacon Road,  
Stone,  
Staffordshire ST15 0SA,  
Great Britain. 
 
Tel: +44(0)1785 812121    
Fax: +44(0)1785 810405 

 

 
 
 
 
 

 
 

Summary of Contents for Electrothermal MC242

























Reviews: