SK
LINE
sportkoncept
11
ASSEMBLY INSTRUCTIONS.-
Take the unit out of its box and make sure that all
of the pieces are there, Fig.1:
(1) Main body.
(14) Pedal (left and right)
(39) Front trim cover.
(61) Main post.
(93) Cushion
(95) Backrest.
(114) Front and rear stabilizer.
(163) Handlebar.
(164) Monitor.
(181) Main tube decoration cover.
(186) Seat handlebar.
(318) Adaptador.
(319) MP3 audio Wire.
(320) Suply Wire.
(190) Allen screw M-5x15.
(191) Spring washer M-8.
(192) Flat washer D8.
(193) Screw M-10x25.
(194) Spring washer M-10.
(195) Flat washer D10.5.
(196) Screw D4x30.
(202) Screw M-8X45.
(203) Screw M-8X20.
(204) Screw D8.
(205) Spring washer M-8.
(206) Screw M-10X50.
(207) Spring washer M-10.
(208) Screw M-6x10.
(212) Screw M-6x25.
Spanner 13-15mm.
Combination spanner.
Allen key 3 mm.
Allen key 6 mm.
1. FITTING THE STABILIZER BARS.-
Rest the main body on a section of foam
packaging, as shown in Fig.2 (this will help with the
assembly work). Take hold of the front stabilizer
bar fitted with wheels (114). Secure with bolts
(206), and washers (207). Tighten securely.
Next, rest the main body (1) on a section of foam
packaging material (this makes assembly easier).
Take the rear stabilizer which is fitted with
adjustable feet (114) and position it on the
machine’s rear stand Fig.2, insert bolts (206) with
the flat washers (207), tighten securely.
2. FITTING THE MAIN POST.-
Take the main post (61) and insert the bottom post
cover (181) in the direction of the arrow, Fig.3.
Slide the main post (61) over the frame post on the
main body, making sure not to snag any of the
cables. Align the main post (61) screw holes with
the frame post screw holes and insert screws (193)
flat washers (194) Grower washers (195) Fig.3.
Tighten securely.
Lower the bottom trim section (181) for the main
post (61) down over the frame post section of the
main body (1) to cover the screws.
4. FITTING THE HANDLEBAR.-
Bring the handlebar (163) up to the underside of
the handlebar stem (61), Fig.4 and attach with
screws (208). Allign the handlebar bracket (168),
then insert screws (169) and tighten.
5. FITTING THE SEAT.-
Bring the handlebar (186) up to the main body
bracket (1) and align holes, Fig.5. Attach with first
with screws (202), spring washers (204) and flat
washers (203) then tighten. Next secure with
screws (203) spring washers (205). Make sure all
screws are tight.
Next, position the seat (93) on the support Fig.5,
secure it using screws (212).
Next, take the backrest (95) and insert it onto the
tube on the seat, Fig.3, Align holes on the backrest
and secure the backrest with screws (190), spring
washers (191) and the flat washers (192).
6. FITTING THE FRONT TRIM COVER.-
Attach the trim cover (39) by sliding it onto the side
tubes, see Fig.7. Next, take screw (196) and
secure the cover by tightening the screw.
7. ATTACHING THE PEDALS.-
Right and left refer to the position that the user
adopts when sitting on the saddle when
exercising.The right-hand pedal, marked with
(14R), screws onto the right-hand crank, marked
(13R), in a clockwise direction. Tighten securely,
figure 7.
The left-hand pedal, marked (14L), screws onto the
left-hand crank, marked (13L), in a counter-
clockwise direction. Tighten securely figure 7.
8. ATTACHING THE MONITOR.-
Unsrew and set aside screws (196), Fig.8, at the
back of the monitor.
Next, connect terminals, sticking out of the handlebar
(61), and terminal (B), sticking out of the monitor
(164), Fig.8.
Place the monitor (164) on top of the plate on the
main post (61), as shown in Fig.8, making sure not to
pinch the wires.
Use screws (252) to hold the monitor in place, Fig.8.
Place the rear and lower monitor covers with screws.
Summary of Contents for H895BM
