background image

17

Type of trouble

Possible causes

Remedies

Rope hard to spool off 

• Wrong setting of the rope pull-
out force 
• Damaged rope 
• Damaged brake band 

• Adjust the rope pullout force 

• Replace the rope
• Replace the brake band 

The winch keeps skidding 
although the clutch was 
deactivated 

• Wrong setting of clutch cylinder hub 
• Damaged drum 
• Damaged clutch disk  
• Drive chains excessively stretched 

• Adjust the hub of the clutch cylinder 

• Replace the drum 
• Replace the clutch 

7.  REPAIRS AND
       MAINTENANCE  

Make sure that the machine is fully disconnected and all mo-

ving parts are secured before performing any maintenance/re-

pair work on the machine. In the event of any malfunctioning, 

switch the machine off before trouble-shooting.

 

7.1     Ordinary maintenance

Make maintenance a regular part of daily operation. The daily mainte-

nance routine needs to include:
• Check for tightness of all screws and nuts.
• Check for visual mechanical damages of the winch.
• Make sure all safety pins are safely in place.
• Check for PTO shaft correct installation and connection and make 

sure that safety shield and chains are duly in place.
• Check the lower hitch points of the tractor and make sure they are 

firmly secured (no cross, horizontal movements).
• Check for proper settings of the clutch, brake and rope pullout force.
• Make sure to fix all problems and anomalies before operating your 

winch.

Perform the following maintenance works, when required or at regular 

time intervals: 
•  Check-up of the hydraulic oil level (if an oil leakage is suspected, in-

spect the entire hydraulic system, hoses and couplings).   

•  Lubricate all moving parts when required.

Summary of Contents for FSW 9.5 HV Profi





























Reviews: