10
- CLONIX/MITTO - Ver. 06
D811324_06
SW2
for CH2 output chanel
1
1
SW1
for CH1output chanel
2 blinks followed by a
pause of about 1 second.
1
1
3 blinks followed by a
pause of about 1 second.
4 blinks followed by a
pause of about1 second.
5 blinks followed by a
pause of about1 second.
6 blinks followed by a pause
of about 1 second.
1
1
NUMBER OF LED DL1 BLINKING SIGNALS
1
1
1
1
When pressing the key SW1 (for channel 1) or SW2 (for channel 2) for the first time, the receiver sets to the programming
mode. Every time the key SW is pressed after that, the receiver switches to the configuration for the subsequent function, that
is indicated by the number of flashings (see table).
For example, if SW2 is pressed for 4 consecutive times, the receiver stores the second channel as timer output
(4 flashings/pause/4 flashings/pause/...).
At this stage, after selecting the channel (SW1 or SW2) and the desired function, the key T (T1-T2-T3 or T4) of the transmitter
will be stored in the memory of the receiver as indicated in the table for programming.
Programming
and
Impulse output
Press the hidden key (Fig.4) on the transmitter until the
LED remains lit, then press the T key (1-2-3 or 4) on
the transmitter until it starts flashing again, wait for the
LED to go off or switch off the power. The transmitter's
T key is now memorized.
TABLE A
LEGEND
Constant blinking.
Automatic memory
storage only
TRC2/MITTO2 with
impulse output
The key T1 of the transmitter is automatically stored on the output
CH1 while the key T2 on CH2. Do not store the TRC1 with this
function (key T2 is not available).
Press the hidden key (Fig.4) on the transmitter until the
LED remains lit, then press key T1 on the transmitter (if
other keys are pressed, they are ignored) until it starts
flashing again, wait for the LED to go off (10 sec) or
transmit a key to exit. T1 and T2 are now automatically
memorized on CH1 and CH2.
Standard Programming
Step-by-step
output
The combined output relay changes its status each time the
transmitter key is pressed.
Press the hidden key P1 (Fig.4) on the transmitter until
the Led remains on, then press the key T (1-2-3 or 4)
on the transmitter until flashing is resumed, wait for the
Led to switch off (15secs.) or disconnect the power
supply. Now the key T of the transmitter is stored with
step-by-step mode.
Timer output
Each time the transmitter key is pressed, the output relay remains
picked up for 90 seconds. If the key is pressed during the counting
cycle, counting is restarted for further 90 seconds.
Press the hidden key P1 (Fig.4) on the transmitter until
the Led remains on, then press the key T (1-2-3 or 4)
on the transmitter until flashing is resumed, wait for the
Led to switch off (15secs.) or disconnect the power
supply. Now the key T of the transmitter is stored with
timer functioning mode.
Advanced Programming
Code elimination
Cancellation of
the entire
receiver memory
WARNING! This operation deletes all of the radiocontrols stored
on channel 1 and channel 2 from the memory of the receiver.
While the LED is flashing, keep buttons SW1 and SW2
on the receiver held down together for longer than 10
sec. The LED flashes very quickly.
By the time the LED goes off, all the transmitters are
deleted and you exit programming mode.
FUNCTION
FUNCTION DESCRIPTION
PROGRAMMING PROCEDURE
N.D.
The associated output relay stays attracted for 1 second.
You will exit programming mode if no memorizing is performed
for 10 seconds.
Non-associated function
