INSTALLATION MANUAL
TABELLA “B” - LOGICHE - (
LOGIC
)
Logic
Definition
Default
Cross
out
setting
used
Optional extras
TCA
Automatic Closing
Time
OFF
ON
Switches automatic closing on
OFF
Switches automatic closing off
3 step
Switches to 3-step
logic
OFF
0N
Logic 3 step
step-by-step mov.
3 STEP
4 STEP
CLOSED
OPENS
OPENS
DURING CLOSING
STOPS
OPEN
CLOSES
CLOSES
DURING OPENING
STOP + TCA
STOP + TCA
AFTER STOP
OPENS
OPENS
OFF
Logic 4 step
ibl open
Block opening
pulses
OFF
ON
The start pulse has no effect during opening.
OFF
The start pulse has effect during opening.
pre-alarm
Pre-alarm
OFF
ON
The flashing light comes on approx. 3 seconds before the motor starts.
OFF
The flashing light comes on at the same time as the motors start.
Photoc.
open
Photocells during
opening
OFF
ON
when beam is broken, operation of the photocell is switched off during opening. During clos-
ing, movement is reversed immediately.
OFF
when beam is broken, photocells are active during both opening and closing. When beam is
broken during closing, movement is reversed only once the photocell is cleared.
test phot
Photocell test
OFF
ON
Switches photocell testing on
OFF
Switches photocell testing on
SCA 2Ch
Gate open light or
2nd radio channel
OFF
ON
The output between terminals 14-15 is set as Gate open light: in this case, the 2nd radio channel
controls partial opening.
OFF
The output between terminals 14-15 is set as 2nd radio channel.
fixed code
Fixed Code
OFF
ON
Receiver is configured for operation in fixed-code mode, see “Radio transmitter cloning” section.
OFF
Receiver is configured for operation in rolling-code mode, see “Radio transmitter cloning” sec-
tion.
radio prog
Remote control
programming
ON
ON
Enables wireless memorizing of transmitters:
1- Press in sequence the hidden key (P1) and normal key (T1-T2-T3-T4) of a transmitter that has
already been memorized in standard mode via the radio menu.
2- Press within 10 sec. the hidden key (P1) and normal key (T1-T2-T3-T4) of a transmitter to be
memorized.
The receiver exits programming mode after 10 sec.: you can use this time to enter other new
transmitters.
This mode does not require access to the control panel.
OFF
Disables wireless memorizing of transmitters. Transmitters are memorized only using the rel-
evant Radio menu.
start-open
START - OPEN
setting
OFF
ON
Input between terminals 3-4 works as OPEN
OFF
Input between terminals 3-4 works as START.
ped-close
PED-CLOSE setting
OFF
ON
Input between terminals 16-17 works as CLOSE.
OFF
Input between terminals 16-17 works as PARTIAL OPENING.
master
Master/Slave
OFF
ON
Control panel is set up as the Master unit in a centralized connection system.
OFF
Control panel is set up as a Slave unit in a centralized connection system.
TABLE “C” – RADIO MENU (
RADIO
)
Logic
Description
Add start
Add Start Key
associates the desired key with the Start command
add 2ch
Add 2ch Key
associates the desired key with the 2nd radio channel command. Associates the desired key with the 2nd radio channel command. If no output
is configured as 2nd Radio Channel Output, the 2nd radio channel controls the pedestrian opening.
erase 64
Erase List
WARNING! Erases all memorized transmitters from the receiver’s memory.
Read receiver code
Displays receiver code required for cloning transmitters.
ON = Enables remote programming of cards via a previously memorized W LINK transmitter.
It remains enabled for 3 minutes from the time the W LINK transmitter is last pressed.
OFF= W LINK programming disabled.
16 -
BOTTICELLI B CRC 480 D01
D811882 00100_03
