background image

 

INTEGRATED ELECTRICAL CABINET

 

Installation, Operation, and Service Manual

 

 

Copyright

 2016:  

Bevco Engineering Company, Inc., 

W222N5739 Miller Way,  Sussex, WI 53089 USA 

IECAX480V125A OM1_R51 Siemens IEC Manual for AX Systems 

                        Page 9 of 14 

 

5.0  INSTALLATION 

 

  The enclosure must be mounted at a height so the top of the main circuit breaker 

handle, when in the ON position, does not exceed 6ft-7in. (2m) above the floor.  (Per 
National Electric Code (NEC # 404.8). 

  Incoming power is connected to the main circuit breaker located at the upper right of 

the Main Disconnect Panel.  Refer to the schematic drawing for the incoming conductor 
size range and tightening torques.  

  There are no conduit knockouts provided in the panel.  The installer must punch the 

conduit holes in the enclosure walls in the desired locations.  The conduits may enter 
on the top, bottom, either side, or in designated areas from the back of the enclosure.  

NOTE:

  When drilling or punching the conduit entry holes, protect the internal 

components from the falling metal chips. 

  All conductors must be sized per the wiring shown on the installation drawings or in the 

system configuration diagram. 

 

1.  Determine the system configuration.   

2.  Note the model of X-Ray Generator.  It will have a rating of 65kW or 80kW. 

3.  Connect the incoming power to the Line side of the Main CB, Q1, terminals L1, L2, and 

L3. 

4.  Connect the X-Ray Generator directly to the load side of contactor K2, terminals 2T1, 

4T2 and 6T3.   

5.  Connect the System Cabinet SC1 directly to the load side of contactor K6, terminals 

2T1, 4T2 and 6T3. 

6.  Connect the IEC Emergency Power Off (EPO) circuits to terminals 1 and 2 of X02. All 

EPOs should have normally closed contacts wired in series.  See EPO wiring diagram. 

7.  Room light controls are on terminals X05 1 through 4. Verify first if the Siemens System 

Cabinet is providing a dry contact or 24V AC or DC.  If 24V AC or DC is provided, 
connect the two wires coming from the Siemens System Cabinet to terminals 1 and 2 of 
X05.  If a dry contact is provided, connect the two wires coming from the Siemens 
System Cabinet to terminals 3 and 4 of X05. See Lighting Wiring Diagram. 

8.  Connect Room light and lighting panel to terminals 5 and 6 of X05. See Lighting Wiring 

Diagram. 

9. 

“X-Ray On” controls are on terminals X06 1 through 4. Verify first if the Siemens 
System Cabinet is providing a dry contact or 24V AC or DC.  If 24V AC or DC is 
provided, connect the two wires coming from the Siemens System Cabinet to terminals 
1 and 2 of X06. If a dry contact is provided, connect the two wires coming from the 
Siemens System Cabinet to terminals 3 and 4 of X06. See Lighting Wiring Diagram. 

10. Connect Warning light and lighting panel to terminals 5 and 6 of X06. See Lighting 

Wiring Diagram. 

11. Connect the Door Switch DSW1 to terminals 1 and 2 of X07.  See Door Switch Wiring 

Diagram. 

12. Connect the Door Switch Connections of the Siemens System Cabinet SC1 to the 

terminals 3 and 4 of X07.  See Door Switch Wiring Diagram. 

Summary of Contents for IECAX480V125A















Reviews: